Sharp SF-DM11 Service Manual Download Page 53

Page: 53 / 141

(5) SF-S18

Unplug the copier and follow the procedure below.

1. Mount the lock plate.

Remove the screws (2) from the upper side of the copier’s left cabinet
panel.
Mount the lock plate to the upper side of the copier’s left cabinet
panel and secure it with the M4 x 8 lockplate screws (2).

2. Mount the support guide.

Hang the two hooks of the support guide on the exit area of the
copier to mount the support guide.

Included parts

Lock plate

(1 pc.)

Support guide

(1 pc.)

Sorter seat

(1 pc.)

Sorter seat cover

(1 pc.)

Sorter seat cover securing screws

(3 pcs.)

Sorter seat securing screws

(4 pcs.)

Spacers
(4 pcs.)

Stopper screw

(1 pc.)

Felt washer

(1 pc.)

Sorter securing screws (M4 x 8)

(2 pcs.)

Lockplate screws (M4 x 8)

(2 pcs.)

Upper left cabinet panel screws

Lock plate

Lock plate screws

Hooks

Support guide

5 – 24

Summary of Contents for SF-DM11














































































































































Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands

Sharp SF-DM11, Service Manual

Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands