Sharp SF-DM11 Service Manual Download Page 31

Page: 31 / 141

B. Installation procedure

(1) SF-2030

1. Releasing optical locks

A. Removing the #2/3 mirror unit lock

Unfasten the screw that holds the #2/3 mirror unit on the left side of
the machine.

B. Releasing the lens and #4/5 mirror unit from lock

Open the paper feed tray and remove two screws that hold the #4/5
mirror unit.

Close the manual tray.

2. Fuser unit set up

A. Removing the fuser unit

While holding up the paper exit handle, open the paper exit cover.

Remove the front panel band on the left side of the front panel in
a manner shown in the figure.

Remove the fuser unit holding two screws.

Hold the fuser unit rotating knob. Push on the front panel and
gently remove the fuser unit.

Do not let the locator pins under the fuser unit hit the ribs on the
front cover.

Hold the fuser unit hand carry strap and remove the fuser unit.

B. Tensioning the heat roller

Move the tension levers on both sides of the fuser unit to the position
shown in the figure. With this, tension is applied to the upper and
lower heat rollers.

C. Installing the cleaning roller

Remove the fusing cover fixing screws (2 pcs.), slide the fusing
cover towards you, and remove it.

Mirror unit holding screw

Paper feed tray

Front panel band

Hand hold strap

Front panel band

Paper exit

Screws

Roller rotating knob

Front panel

Fuser unit

Ribs

Locator pins

Front side

Rear side

Tension lever

Screws

Fuser cover

Fuser unit

5 – 2

Summary of Contents for SF-DM11














































































































































Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands

Sharp SF-DM11, Service Manual

Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands