37
SESAMO
DUALCORE
USER MANUAL
Recipient and use of the manual
These instructions are intended for the operator or the user of a SESAMO DUALCORE SERIES
automatic door system. So that you get the most out of your automated system, Sesamo
recommends you read and follow the installation and usage instructions in this manual
carefully. This device has been designed for the automation of sliding pedestrian doors. Any
other use is considered contrary to the use intended by the manufacturer, who will therefore
accept no liability for the consequences. Do not tamper with or alter the internal equipment of
the automated system or the safety devices present in the control CPU. The manufacturer
denies any responsibility of internal parts on the automated system are tampered with or
altered or if safety devices different to those indicated by the manufacturer are used.
Description of the DUALCORE SERIES automated system operation
By feeding the automated system with 230V mains voltage, it performs a low-speed maneuver
in closing phase; if the door is already closed it remains in this position, and after a few
seconds it is ready to operate.
The basic or advanced selector will remain positioned in the logic preceding the lack of mains.
At this point the automated system is ready to operate in ways that depend on the type of
peripheral devices and accessories installed and on the logic selected by means of the selector;
it will perform automatic opening and closing of the window so as to allow the passage of
people in complete safety and continuously.
The opening of the leaves can be controlled by detection sensors, by the advanced or basic
selector and by buttons for manual control; the opening maneuver can be followed by a stop
or by automatic re-closing according to the chosen logic (see selector logic description).
The stop of the doors in the open position allows the passage of people according to the
customer's needs; the stop time can be adjusted during installation.
The closing of the leaves takes place automatically at the end of the stop time, with a lower
speed than the opening.
During installation it is possible to select a particular type of operation called "semi-
automatic"; in this condition the closing of the leaves does not take place automatically but
must be controlled manually by means of a suitable button.
The safety of the automated system is entrusted to the active safety sensors that detect the
presence of obstacles in the sliding area and possibly prevent the doors from closing again.
Summary of Contents for DUALCORE LH100
