31
SESAMO
DUALCORE
DIAGNOSTICS
Memory data view
The Dualcore processor display allows you to view the values saved by the system during
operation and programming, such as: firmware version loaded, number of maneuvers
performed, etc.
To view the value desired, proceed as follows:
1-
press the - keys on the display until the "In" code appears then press ENT: the
display will show the code 0;
2-
press the + keys to scroll through the codes (0, 1, 2, ...) to the one desired then
press ENT: the table below explains the meanings of each of the codes;
3-
the display will show the value of the parameter consulted for 20 seconds using a
variable display type depending on the length of the value;
4-
press ESC or wait to 20 seconds to return to the previous menu, at this point you
can consult another parameter by following the same sequence or exit from the
consultation by pressing ESC again;
Parameter
Description
0
firmware version of the user controller e.g. 2:00
1
firmware version of the safety controller e.g. 2.00
2
type of automated system C0, C1,… see table below
3
total weight of the moving mass: P0 (0-100kg); P1 (100-200kg); P2 (200-
300kg)
4
total number of operations performed by the control unit.
5
sensor configuration installed: refer to the S code table in the description
section of the LS procedure
Warning
Description
C0
LH100 automated system (
LI
indication on main key)
C1
LH140 automated system (
Pk
indication on main key)
C2
Master control unit RD100 automated system (
SM
indication on main
key)
C3
Slave control unit RD100 automated system (
SS
indication on main key)
Note: each time the Dualcore control unit is powered or the reset button is pressed, the
display shows the information 0/2/1/ and type of sensors used in order e.g. S3
DANGER: the total weight of the mass in movement refers to the weight of a single
leaf for single leaf installations and the combined weight of the two leaves for double leaf
installations
Summary of Contents for DUALCORE LH100
