15
SESAMO
DUALCORE
MECHANICAL ASSEMBLY FINAL CHECKS
Before commissioning the automated systems, check and carry out the following operations:
• carefully remove any dust
or burr residue from the slide rails and carriage wheels
• check that all screws of the components of the automated system are properly tightened
• check the correct tension of the belt
• check that the cables are fixed and that no cables run near the tran
sit area of the carriages
or belt
• check that the limit switches are positioned correctly and that the belt clamps do not
knock against the toothed pulleys
• apply a thin layer of standard grease to the bearings on the slide rail and
transmission belt
WARNING: The slide rail and the transmission belt do not need lubrication and can
work without showing signs of wear. Nevertheless, lubrication prevents the onset of noise
emission if parts are not perfectly aligned.
WARNING: for proper operation it is very important to make sure that there are no
mechanical impediments or frictions that hinder the movement throughout the sliding
area of the leaves: in case of doubt, perform a manual dragging test with a dynamometer
to identify any points with excessive friction.
D
UALCORE PROCESSOR
:
FUNCTION AND WARNINGS
The Dualcore processor is designed to manage automated systems produced by Sesamo,
complies with the specifications of EN16005 and can function with peripherals that comply
with the same regulation in order to allow the creation of fully automated doors in line with
the highest safety standards.
The Dualcore processor may only be used for automated systems produced by Sesamo of
the Dualcore series and must be configured and installed by professionally qualified
personnel, following the instructions provided in this manual with particular attention to the
information marked: danger, warning, note.
hazard, warning, note.
The Dualcore processor is designed to configure its own operating parameters through self-
learning, guaranteeing quick and easy installation.
DANGER: do not wash, disassemble, modify, repair or remove the protective covers
of the electronic components and the Dualcore processor, as this could lead to fatal
electric shock or irreparably damage the product.
DANGER: do not carry out any operation on the Dualcore control unit, except for the
adjustments by means of the specific buttons, without having previously disconnected the
power supply plug (fig. 21 part. L), otherwise fatal electric shocks or irreversible damage of
the product could occur.
Summary of Contents for DUALCORE LH100
