Seeley coolair Braemar Breezair MaglQcool Service Manual Download Page 42

Page: 42 / 68

MAGIQTOUCH & MAGIQCOOL MODELS

Refit the pad frames by locating the bottom

edge in the tank groove, then push the top into

the lid.

ILL976-D

REFITTING THE PAD FRAMES FOR

BRAEMAR LCQI / LCQ / LCS / BMQ &

COOLAIR CPQ EVAPORATIVE COOLER

Component

Part No.

Watts

Total Max

Amps

Fan Motor

(Variable)

116907

340W

2.2

116914

430W

3.5

116921

600W

4.5

116938

950W

6.3

Component

Part No. Voltage

Ohms

Tornado

095806

240Vac

122 ±6

Drain valve

115986

12VDC

Solenoid valve

865607

12VDC

19.2±10%

Cooler

Electronics Box

116341

Solenoid Cable

865614

Water

Management

Probe

865621

QUICK REFERENCE GUIDE

BRAEMAR LCQI EVAPORATIVE

COOLER

cont

•  Clean the metal probes
•  Set the multimeter to ohms mode
•  Pin 1 - Blue wire = approx. 0 (zero) ohms
•  Pin 2 - Black wire = approx. 0 (zero) ohms
•  * Pin 3 - Brown wire = approx 0 (zero) ohms

(3 prong probes only)

# A reading of 5 ohms or greater indicates

faulty probes.

* The brown wire (Pin 3) is not connected on 2

prong probes.

If the probe continues to fault, check between

the contacts to ensure there are no short

circuits.

PIN 1 (BLUE)
PIN 2 (BLACK)
PIN 3 (BROWN)
PIN 4 (EMPTY)

0.00

ILL2232-A

Pin 1

Pin 2

WATER SALINITY PROBE TESTING

NOTE:

The Salinity Probe plug connector for

LCQI coolers differs to the EXQ/LCQ, but the

wire colours and pin-outs are identical.

Summary of Contents for coolair Braemar Breezair MaglQcool





































































Search results

Summary of Contents for coolair Braemar Breezair MaglQcool

Reviews:

Related manuals for coolair Braemar Breezair MaglQcool

Brands by name

Popular brands

Seeley coolair Braemar Breezair MaglQcool, Service Manual

Search results

Summary of Contents for coolair Braemar Breezair MaglQcool

Reviews:

Related manuals for coolair Braemar Breezair MaglQcool

Brands by name

Popular brands