Seeley coolair Braemar Breezair MaglQcool Service Manual Download Page 61

Page: 61 / 68

SEELEY INTERNATIONAL

- SERVICE GUIDE

Issue

Possible Cause

What to Check

What to Do

At the beginning of
a new installation,
the MagIQtouch
controller is not
showing the Power
Up screen.

MagIQtouch controller
has already been used
to control another
system.

First screen displayed
should be the Power Up
screen with following
options:
“All New System”
or
“Existing system with new
MagIQtouch controller”

Press the Reset located at
the rear of the controller.
Select “MagIQtouch control-
ler Only”.
Start Installation.

An appliance is
not detected
during installation.

Incorrect wiring.

Check:
1. Cable connections are
good
2. Link Module dipswitches
set correctly
3. Cable lengths are as per
recommendations

Modify wiring if required.
Make sure all the appliances
are connected and powered
up.

The appliance/control
board was already
installed in a previous
system.

Reset Whole System (back
Reset button).
Power OFF/ON whole
System.
Start Installation.

The Master Air
Sensor has not
been detected.

Incorrect wiring.

Check:
1. Cable connections are
good
2. Link Module dipswitches
set correctly
3. Cable lengths are as per
recommendations

Modify wiring if required.
Make sure all the appliances
are connected and powered
up.

Wrong dipswitch
setting on the Link
Module

If Air Sensor plugged into
Link Module connector
next to dipswitch, then
dipswitch should be set
to ON

Ensure dipswitch is set to
ON.

The Air Sensor was
already installed in a
previous system.

Reset Whole System by
(back Reset button).
Power OFF/ON whole
System.
Start Installation

The MagIQtouch
controller
displays: “More
than one

unconfigured

appliance
connected.”

Two or more uncon-

figured appliances of

the same type have
been connected to the
system at the same
time.

Identify the recently
connected appliances.

Disconnect all but one of
these recently connected
appliances.
Select “Retry”.

MAGIQTOUCH SYSTEM

TROUBLESHOOTING GUIDE

Summary of Contents for coolair Braemar Breezair MaglQcool





































































Search results

Summary of Contents for coolair Braemar Breezair MaglQcool

Reviews:

Related manuals for coolair Braemar Breezair MaglQcool

Brands by name

Popular brands

Seeley coolair Braemar Breezair MaglQcool, Service Manual

Search results

Summary of Contents for coolair Braemar Breezair MaglQcool

Reviews:

Related manuals for coolair Braemar Breezair MaglQcool

Brands by name

Popular brands