Seeley coolair Braemar Breezair MaglQcool Service Manual Download Page 27

Page: 27 / 68

SEELEY INTERNATIONAL

- SERVICE GUIDE

ILL1660-A

Colour Flash

Indicates

glow

No power or a failure has

occurred. (Check power

supply to cooler including

isolating switch, circuit

breaker and plug and

socket connection in the

roof space)

Green

Every 2 sec Normal Operation

Red

1 Flash

Fault Code #1

Communication Failure

2 Flashes

*Fault Code #2

Failure to detect water at

probes within 20 mins.

4 Flashes

*Fault Code #4

Failure to clear probes

during drain within 20 mins.

9 Flashes

Fault Code #9

Incorrect Supply Frequency.

ILL1661-A

SALINITY LED

The bottom LED is red only and displays

salinity setting information for evaporative

coolers installed. Parameters are set by

MagIQtouch or MagIQcool wall controllers.

Refer to pages 17 or 21.

BREEZAIR EXQ / EZQ / EXS

EVAPORATIVE COOLER

cont

Sal Flash

Indicates

OFF

Not Applicable

1 Flash

WaterMiser

salinity is below the

set point.

2 Flash

WaterMiser

salinity is above the

set point.

3 Flash

The Salinity Control Method is set

for Timed Drain

4 Flash

Bleed Tray - No Drain Valve.

5 Flash

Thermostatic Control (no Water)

operation set.

Continuously

(When probes

immersed in

water)

Water not detected. The probes

are immersed in water but are

open circuit, or measured salinity

is less than 20µs/cm (the water

has very little salt content).

Continuously

(No water in

tank)

WaterMiser

/ Drain Valve option

is active

DIAGNOSTIC LED

The top LED glows green or red acting as a

diagnostic indicator. If the top LED is double

flashing green, everything is ok, this is normal

operation.

Salinity LED Indication for evaporative coolers

fitted with drain valves.

Sal Flash

Controller Salinity Setting

5 Flash

Salinity Control set

5 Flash

Timed Drain

4 Flash

The Salinity Control method is set

for continuous bleed

(bleed tray used)

5 Flash

Thermostatic Control No Water

(no water) operation

Salinity LED Indication for evaporative coolers

fitted with bleed trays and shorting links only.

*FAULT CODE 02 (2 Red Flashes)

Failure to detect water at probes within 20

minutes

*FAULT CODE 04 (4 Red Flashes)

Failure to clear probes during drain within 20

minutes

Refer to section

“DIAGNOSTICS FAULT

CODES”

on page 31 for more detail on

troubleshooting these fault codes.

Summary of Contents for coolair Braemar Breezair MaglQcool





































































Search results

Summary of Contents for coolair Braemar Breezair MaglQcool

Reviews:

Related manuals for coolair Braemar Breezair MaglQcool

Brands by name

Popular brands

Seeley coolair Braemar Breezair MaglQcool, Service Manual

Search results

Summary of Contents for coolair Braemar Breezair MaglQcool

Reviews:

Related manuals for coolair Braemar Breezair MaglQcool

Brands by name

Popular brands