![Sea-doo 2003 GTI LE RFI Shop Manual Download Page 15](http://html.mh-extra.com/html/sea-doo/2003-gti-le-rfi/2003-gti-le-rfi_shop-manual_1221429015.webp)
XII
SMR2003_001_00_00A2.FM
Standard Thread Repair
1. Follow instructions on Loctite FORM-A-THREAD
81668
package.
2. If a plate is used to align bolt:
a. Apply release agent on mating surfaces.
b. Put waxed paper or similar film on the surfaces.
3. Twist bolt when inserting it to improve thread
conformation.
NOTE:
NOT intended for engine stud repairs.
Repair of Small Holes/Fine Threads
Option 1: Enlarge damaged hole, then follow
Stan-
dard Thread Repair
procedure.
Option 2: Apply FORM-A-THREAD
on the screw
and insert in damaged hole.
Permanent Stud Installation (light duty)
1. Use a stud or thread on desired length.
2. DO NOT apply release agent on stud.
3. Do a
Standard Thread Repair
.
4. Allow to cure for 30 minutes.
5. Assemble.
GASKET COMPOUND
All Parts
1. Proper strength Loctite
2. Loctite Primer N (P/N 293 800 041) and Gasket Eliminator 518
(P/N 293 800 038) on both sides of gasket
3. Loctite Primer N only
1. Remove old gasket and other contaminants
with Loctite Chisel remover (P/N 413 708 500).
Use a mechanical mean if necessary.
NOTE:
Avoid grinding.
2. Clean both mating surfaces with solvent.
3. Spray Loctite Primer N on both mating surfaces
and on both sides of gasket. Allow to dry 1 or 2
minutes.
4. Apply GASKET ELIMINATOR 518 (P/N 293 800
038) on both sides of gasket, using a clean ap-
plicator.
5. Place gasket on mating surfaces and assemble
immediately.
NOTE:
If the cover is bolted to blind holes (above),
apply proper strength Loctite in the hole and on
threads. Tighten.
If holes are sunken, apply proper strength Loctite
on bolt threads.
6. Tighten as usual.
MOUNTING ON SHAFT
Mounting with a Press
1. Bearing
2. Proper strength Loctite
3. Shaft
Standard
1. Clean shaft external part and element internal
part.
2. Apply a strip of proper strength Loctite on shaft
circumference at insert or engagement point.
NOTE:
Retaining compound is always forced out
when applied on shaft.
3. DO NOT use anti-seize Loctite or any similar
product.
4. No curing period is required.
A00A3SA
2
1
1
3
1
A00A3UA
1
2
3
INTRODUCTION
www.SeaDooManuals.net
Summary of Contents for 2003 GTI LE RFI
