SCP SCIENCE DigiPREP Service Manual Download Page 28

Page: 28 / 88

SCP SCIENCE

KeyPad
Version 1.0

THE

Digi

PREP

BLOCK IS NOT HEATING UP

DigiPREP connection verifi cation

• Ensure that the cable between the KeyPad

controller and the heating block is correctly
inserted on both sides.

• Verify that the voltage selector of the heating

block is properly set.

COM2 dongle verifi cation

When the

COM2

of the KeyPad

controller is not connected to a

Digi

SET

system, the port must be

shorted.

• Make sure that sections 1 and 2 have been verifi ed
before continuing.

• Ensure that the

Digi

SET

dongle is fully inserted

into

COM2

port (see fi gure 2)

• If so, before opening the bottom plate, verify with

a multimeter that the

COM2

dongle is shorted. If

not, replace the part with a new one.

• If the dongle is ok, remove the bottom by

removing the 4 screws that hold the feet in place.
Check if the

Digi

SET

cable (see fi gure 15 for

position) is fully inserted.

FIGURE 15:

DIGI

SET

CONNECTOR LOCATION

Legend

Digi

SET

connector

INTERNAL WIRING CONNECTION VERIFICATION

  • After removing the bottom plate, verify the
    connectivity between the heating block external
    connector and the PCB (see fi gure 16).

FIGURE 16: HEATING BLOCK CONNECTOR LOCATION

Legend
1. Heater connector (Hot heating block)
2. Neutral connector (Neutral heating block)
3. Earth Ground

DIGISET VERIFICATION (ONLY IF APPLICABLE)

Make sure that the

Digi

SET

is fully fonctional (see

NOTE

Summary of Contents for DigiPREP

























































































Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands

SCP SCIENCE DigiPREP, Service Manual

Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands