SCP SCIENCE DigiPREP Service Manual Download Page 11

Page: 11 / 88

KeyPad

Version 1.0

SCP SCIENCE

UNPACKING

Retain all packing material in case

you need to return the instrument to

the manufacturer for service.

1. Verify that all components listed have been

included:

•

Digi

PREP

keypad controller

• Power

cord

•

Digi

SET

dongle

COMPONENTS AND INSTRUMENT DESCRIPTION

Inspect the products for any shipping damage.
If the instrument has been damaged in shipping,
contact the freight carrier to report damage and to
fi le a damage report. Also contact the

SCP

SCIENCE

service department to report damage

and to request service information (see page 88 for
contact information).

If damage is noted, do not attempt

to operate the instrument.

1. Power light (LED)

2. LCD

screen

3. KeyPad

4. Connection port for umbilical cord (to block)

5. Power cord receptacle

6. Power

Switch

Digi

SET

connection port

8. Detachable Power Cord

NOTE

WARNING

Power cord

Summary of Contents for DigiPREP

























































































Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands

SCP SCIENCE DigiPREP, Service Manual

Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands