SCP SCIENCE DigiPREP Service Manual Download Page 74

Page: 74 / 88

SCP SCIENCE

KeyPad
Version 1.0

Digi

PREP

DISMANTLING PROCEDURES

This section deals with dismantling the unit to
gain access to the components inside. There have
been several electrical revisions to the

Digi

PREP

systems. If you do not fi nd instructions for your model,
continue reading.

REMOVING THE CORIAN RING

1. Turn the

Digi

PREP

Block on its side to obtain

the key

• If you fi nd an aluminium T: Continue to step

• If you don’t fi nd an Aluminium T: The Corian

ring is designed to lift off the top of the

instrument manually. Pull up gently on each

corner until the top lifts off, and continue to

'Removing the graphite block'

2. Insert the key into one of the slots located
beside the rubber feet.

3. Push the aluminium T into the slot until the
Corian ring begins to lift.

  4. Repeat process for the three remaining clips,
    and return the aluminium key to the base of the
    unit.

If you are missing your aluminium

key, a substitution such as a fl at

head screwdriver will also work.

NOTE

Summary of Contents for DigiPREP

























































































Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands

SCP SCIENCE DigiPREP, Service Manual

Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands