SCP SCIENCE DigiPREP Service Manual Download Page 77 | Manualshive

Page: 77 / 88

background image

KeyPad

Version 1.0

SCP SCIENCE

77

To verify the over temperature protection switch
is closed, measure between pin 7 and pin 9: this
should return a resistance based on the resistance
of the heater mat (see table on page 88).

UMBILICAL CORDS, S104

The S104 umbilical harness is the power, and
communication medium between the block and
the controller. There are two formats of umbilical
cords: the new version includes Jr blocks with
s/n JR640404137 forward, HP Blocks with
s/n 9241030022 forward, MS blocks with s/n
MS45030019 forward, and any LS block. Any
previous serial numbers have the old format umbilical
harness.

New-style umbilical harness tests

1. Place the multi-meter on the continuity setting.

  2. Measure between pin 2 and the graphite block.
    This should return continuity. Ensure you pick a
    spot that is not covered with Tefl on.

3. Measure between pin 2 (ground) and each pin
individually. No pins should return continuity.

4. Measure between pin 4 (EX+) and pin 6 (M+).
This should return continuity.

5. Measure between pin 1 (EX-) and pin 3 (M-).
This should return continuity.

  6. Measure between pin 7 (L) and pin 9 (N). This
    should return a resistance based on the following
    table:

MODEL

VOLTAGE SELECTOR

SWITCH POSITION

RESISTANCE

Digi

PREP Jr

115V
230V

18



± 2



71



± 2



Digi

PREP MS

115V
230V

15



± 2



57



± 2



Digi

PREP HP

115V
230V

15



± 2



57



± 2



Digi

PREP LS

230V

20



± 2



Digi

PREP HT

230V

16



± 2



7. Measure between pin 6 on the umbilical cord
(M+/EX+) and pin 1 of the dongle port. This
should return continuity.

8. Measure between pin 3 on the umbilical cord
(M-/EX-) and pin 3 of the dongle port.
This should return continuity.

Old-style umbilical harness tests

Instruments with the old-style umbilical harness
are for Junior blocks with s/n JR640404136 and
earlier, HP blocks with s/n 9241030021 and earlier,
and MS blocks with s/n MS45030019 and earlier.
Please note this style is discontinued and can no
longer be purchased. All LS blocks have the new
form of umbilical cord.

«
...
75
76
77
78
79
...
»

Summary of Contents for DigiPREP

























































































Reviews:

No comments

Related manuals for DigiPREP

Brand: wattio Pages: 20

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

Brand: rada Pages: 16

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: VAT Pages: 27

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

FrameSaver 9120

Brand: Paradyne Pages: 20

VeriSafe VS2-NET

Brand: Panduit Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands