SCP SCIENCE DigiPREP Service Manual Download Page 33 | Manualshive

Page: 33 / 88

background image

KeyPad

Version 1.0

SCP SCIENCE

33

A/D CONVERSION PROBLEM

If the section 5 has been fully investigated and
the system does not provide the right temperature
readings, verify the analog supply and the analog ref-
erence voltage of the microcontroller U6.

  • With the negative lead of a multimeter on the via
    connected to pad C25-1 and its possible lead on
    the via connected to pd C25-2, you should read
    5Vdc.

  • With the negative lead of a multimeter on the via
    connected to pad C25-1 and its positive lead on
    the via connected to pin U6-27, you should read
    5Vdc.

If those values are less than 4.8V, replace the
KeyPad PCB.

CPU UNSTABLE

If CPU is resetting by itself, check pin 9 of U6.
WIth the negative lead of a multimeter on pin 3 of J1
and its positive lead on pin 1 of J1, you should read
a steady voltage value of at least 3.7 Vdc. If not, re-
place the KeyPad PCB.

«
...
31
32
33
34
35
...
»

Summary of Contents for DigiPREP

























































































Reviews:

No comments

Related manuals for DigiPREP

Brand: Bartlett Pages: 30

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: Eaton Pages: 166

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 26

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands