SCP SCIENCE DigiPREP Service Manual Download Page 50

Page: 50 / 88

SCP SCIENCE

KeyPad
Version 1.0

Unpacking

Retain all packing material in case you

need to return the instrument to the

manufacturer for service.

Verify that all components listed have been

included:

• Digi

PREP HT

system

• Operation

manual

• Exhaust

Manifold

•  Dual-Zone Tube Rack
•  Rack and Manifold support
•  Thumb screws (6pc)
• Drip

tray

• Exhaust connection hose
• Water

Jet

• Boiling

Rods

Digi

PREP HT

BLOCK DESCRIPTION

Optional items, such as glass,

quartz, calibrated or non-calibrated

digestion tubes may have been

included in the shipment. Carefully

check the packing list(s) and the

contents of shipping cartons to

verify that all items listed are included.

Please notify

SCP SCIENCE

your local distributor of any

discrepancies.

Inspect the products for any shipping damage.
If the instrument has been damaged in shipping,
contact the freight carrier to report damage and
to fi le a damage report. Also contact the

SCP

SCIENCE

service department to report damage

and to request service information (see page 88 for
contact information).

If damage is noted, do not attempt to

operate the instrument.

1. Exhaust manifold module

2. Dual-zone Tube Rack

3. Umbilical cable (to connect to controller)

4. Digestion

Tubes

5. Drip Tray

6. Thumb Screws (6)

7. Dual

PROBE

Connection (option)

8. Glass Water Jet

NOTE

WARNING

Boiling Rods
(pack of 40)

Heat Shield (optional)

Summary of Contents for DigiPREP

























































































Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands

SCP SCIENCE DigiPREP, Service Manual

Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands