SCP SCIENCE DigiPREP Service Manual Download Page 48 | Manualshive

Page: 48 / 88

background image

SCP SCIENCE

48

KeyPad
Version 1.0

Symbol

Description

Symbol

Description

V

Voltage

l

Mains on

~

Alternating current

0

Mains off

A

Current

Attention, consult

accompanying documents

Hz

Frequency

Caution, hot surfaces

F

Fast-acting fuse

Protective conductor terminal

CAUTIONS AND NOTES

Cautions, warnings, and notes are included
throughoutthis manual.

CAUTION

A caution is used to emphasize information
pertaining to procedures that, if not
strictly followed, may result in damage
or destruction to the instrument or
improper instrument operation.

WARNING

A warning is used to emphasize information
about dangerous or hazardous conditions
relating to the operation, cleaning, or
maintenance of the instrument that may
result in personal injury.

NOTE

A note is used to emphasize procedures
or conditions that may be misinterpreted
or overlooked, and to clarify potentially
confusing situations.

WARRANTY

SCP SCIENCE

warrants this product free

from defect in workmanship and materials
for one (1) year from date of purchase.

•

Should the unit malfunction, call

SCP

SCIENCES

's service department (see page

92), or your local distributor. and a service
representative will instruct you on how to
proceed.

• There are no user-serviceable parts in this unit.

The warranty is void if the unit shows evidence
of being tampered with, of being subjected to
excessive moisture, heat or corrosion, or of other
misuse.

•

SCP SCIENCE

shall not be responsible for

any damage or losses however caused which
may be experienced as a result of the installation
or use of this product.

• This product is not warranted for, nor has it

been tested for, use with perchloric acid.
The user accepts all responsibility if this product
is used with perchloric acid.

• The controller must be placed outside the fume

hood.

NOTE

CAUTION

WARNING

«
...
46
47
48
49
50
...
»

Summary of Contents for DigiPREP

























































































Reviews:

No comments

Related manuals for DigiPREP

Brand: IFM Pages: 49

Brand: K'Nex Education Pages: 56

Brand: Rabbit Pages: 38

PDS CONTROL Series

Brand: S&P Pages: 32

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Brand: Rain Bird Pages: 48

Brand: Sullair Pages: 31

Level-Trac LT-310

Brand: QTS Pages: 12

Enclosure ENCR-10

Brand: suprema Pages: 18

Brand: M-system Pages: 16

iMcV-DS3-LineTerm

Brand: B&B Electronics Pages: 11

Brand: Global Water Pages: 7

Brand: Gardenic Pages: 14

Brand: Carel Pages: 2

Reference 20 Plus A/V System Controller

Brand: B&K Pages: 84

Brand: YASKAWA Pages: 38

Brand: Forte Pages: 2

Brand: HEIDENHAIN Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands