SCP SCIENCE DigiPREP Service Manual Download Page 62

Page: 62 / 88

SCP SCIENCE

KeyPad
Version 1.0

Digi

PREP JR

BLOCK DESCRIPTION

Digi

PROBE

Connector-Connection port

for

Digi

PROBE

Digi

PROBE

will allow

direct monitoring and control based on

actual sample temperature.

Digi

PROBE

Dongle must be installed to run the

Digi

PREP Jr

without the

Digi

PROBE

option.

2. Cable Connector – Connection port for the

Digi

PREP Jr

umbilical cable to the

controller.

3. Power Switch/ Power Cord Receptacle –

On/Off switch – contains circuit breaker

and receives the female end of the power

cord.

Digi

SET

Connector – Connection port

for

Digi

SET

Digi

SET

will automatically

shut off the digestion block when a pre-set

sample volume is reached.

Digi

SET

dongle must be installed to run

Digi

PREP

without the

Digi

SET

option.

Digi

PREP

Controller –

Digi

PREP Jr

designed to be used with

Digi

PREP

KeyPad* or Touch Screen* controller

(*Sold separately)

Digi

PROBE

(Option) – To monitor and

control sample or block temperature.

Digi

PROBE

Storage Well – Use with

replaceable glass liner.

8. Voltage Selector Switch - Select appropriate

voltage. If 115 V is showing, system is

running at 115 volts.

Summary of Contents for DigiPREP

























































































Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands

SCP SCIENCE DigiPREP, Service Manual

Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands