SCP SCIENCE DigiPREP Service Manual Download Page 80

Page: 80 / 88

SCP SCIENCE

KeyPad
Version 1.0

2. Peel the heater off of the graphite block and

ensure there is a Tefl on sheet between the

heater and the graphite block. Check the

integrity of the Tefl

on sheet. Clean any

particles off the surface with alcohol.

3. Apply silicon sealant to the Tefl on sheet.

4. Using a smooth but rigid piece of material, spread
the silicon sealant evenly so that a thin layer covers
the surface where the heater will rest.

5. Place the new heater on the surface of the
Tefl

on sheet and remove any air bubbles

between the Tefl

on sheet and the heater

by planing a smooth but rigid piece of material
across the surface.

  6. Reconnect the wiring of the new heater to the
    wires originally cut in section 1; there is
    no polarity to the black wires as they are AC.
    Use the following table to connect the correct
    colors to the correct locations:

White wire

Connects to neutral of the heater pad

Parallel connection

Between jumper from 2a

and black heater wire (live)

Parallel connection

Between black heater wire (live) and

over-temperature protection switch

  7. Check the resistance of the heater between
    pin 7 and pin 9 to ensure that the heater has

been properly reconnected. Consult the

following table of resistances to ensure the
correct

values:

Summary of Contents for DigiPREP

























































































Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands

SCP SCIENCE DigiPREP, Service Manual

Search results

Summary of Contents for DigiPREP

Reviews:

Related manuals for DigiPREP

Brands by name

Popular brands