manualshive.com logo in svg

SCP SCIENCE DigiPREP, Service Manual

The SCP SCIENCE DigiPREP is a cutting-edge laboratory equipment designed for efficient sample preparation. Ensure seamless operation with the comprehensive Service Manual, available for free download from manualshive.com. This manual provides step-by-step instructions, troubleshooting tips, and maintenance guidelines to maximize your DigiPREP's performance and longevity.

Share
Download
background image

KeyPad

Version 1.0

SCP SCIENCE

3

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................... 7

WARRANTY .......................................................................................................................................... 7

BASIC VERIFICATION LIST ..................................................................................................................... 8

KEYPAD INSTRUCTION MANUAL

CAUTIONS, NOTES, SYMBOLS, SAFETY INFORMATION,WARRANTY ................................................. 10

COMPONENTS AND INSTRUMENT DESCRIPTION .............................................................................. 11

 Unpacking 

................................................................................................................................... 11

INSTRUMENT OPERATION .................................................................................................................. 12

 KeyPad 

icons 

.............................................................................................................................. 12

SCREENS ........................................................................................................................................... 13

 Banner 

screen 

............................................................................................................................. 13

 Menu 

screen 

............................................................................................................................... 13

 Utilities 

screen.............................................................................................................................. 13

 Language 

screen 

......................................................................................................................... 13

 System 

screen 

............................................................................................................................. 13

OPERATING PARAMETERS ................................................................................................................. 14

 Run 

screen 

.................................................................................................................................. 14

 Calibration 

screen 

........................................................................................................................ 14

SAFETY MESSAGES ........................................................................................................................... 15

 

Possible Safety Messages............................................................................................................ 15

 

Preventing Safety Messages ........................................................................................................ 16

 

Disabling Safety Messages ........................................................................................................... 16

Digi

PROBE 

ERROR MESSAGES........................................................................................................ 17

DIAGNOSTIC TEST PROCEDURE ........................................................................................................ 17

CLEANING .......................................................................................................................................... 17

SPECIFICATIONS KEYPAD .................................................................................................................. 18

 Electrical 

...................................................................................................................................... 18

 Environmental 

.............................................................................................................................. 18

KEYPAD SERVICE MANUAL

KEYPAD GENERAL DESCRIPTION ....................................................................................................... 20

LIGHT EMITTING DIODE & LCD ........................................................................................................... 21

KEYPAD MALFUNCTION ..................................................................................................................... 22

FAILED KEYPAD BUTTONS ................................................................................................................. 23

KEYPAD DIAGNOSTIC SECTION ......................................................................................................... 23

UIPS POWER SUPPLY SECTION ......................................................................................................... 24

HEATER DRIVE SECTION .................................................................................................................... 27

THE BLOCK IS NOT HEATING UP ....................................................................................................... 28

Summary of Contents for DigiPREP

























































































Reviews:

No comments

Related manuals for DigiPREP

Harmonic Drive LA Series Manual preview
LA Series
Brand: Harmonic Drive Pages: 25
Nelson MR Technical Application Manual preview
MR
Brand: Nelson Pages: 8
Lattice Semiconductor CrossLink-NX Quick Start preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 2
Lathem PC600 Series Quick Start Manual preview
PC600 Series
Brand: Lathem Pages: 4
tams elektronik HADES Manual preview
HADES
Brand: tams elektronik Pages: 36
Rain Bird ESP-LXD Installation, Programming & Operation Manual preview
ESP-LXD
Brand: Rain Bird Pages: 138
Eaton SCD24 Installation Manual preview
SCD24
Brand: Eaton Pages: 8
ABB RHDE250 Operating Instruction preview
RHDE250
Brand: ABB Pages: 44
Omega CNI16D Quick Start preview
CNI16D
Brand: Omega Pages: 2
Zmotion ZMC408SCAN Hardware Manual preview
ZMC408SCAN
Brand: Zmotion Pages: 34
Ban Seok BV-322M User Manual preview
BV-322M
Brand: Ban Seok Pages: 9
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Brand: Data Signs Pages: 23
M-system R3-PD16B Instruction Manual preview
R3-PD16B
Brand: M-system Pages: 10
bihl+Wiedemann BW3489 Installation Instructions Manual preview
BW3489
Brand: bihl+Wiedemann Pages: 16
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Brand: Acuity Controls Pages: 5
Risco ProSYS 128 Programming Manual preview
ProSYS 128
Brand: Risco Pages: 232
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Brand: Bard Pages: 2
Delabie PREMIX COMPACT Manual preview
PREMIX COMPACT
Brand: Delabie Pages: 20

Brands by name

Popular brands

Load more brands