Scientific SMO1000A-S User Manual Download Page 64

Page: 64 / 176

User Manual SMO1000A-S

64/176

Figure 21 Turn off the Noise Reject

Figure 22 Turn on the Noise Reject

If the signal you are probing is noisy, you can set up the oscilloscope to reduce the noise

in the trigger path and on the displayed waveform. First, stabilize the displayed waveform

by removing the noise from the trigger path. Second, reduce the noise on the displayed

waveform.

Connect a signal to the oscilloscope and obtain a stable display.

Remove the noise from the trigger path by setting trigger coupling to

LF Reject

Reject

or turning on

Noise Reject

Set the

Acquisition

option to Average to reduce noise on the displayed waveform.

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands