Scientific SMO1000A-S User Manual Download Page 16

Page: 16 / 176

User Manual SMO1000A-S

16/176

General Inspection

Inspect the shipping container for damage.

Keep the damaged shipping container or cushioning material until the contents of the

shipment have been checked for completeness and the instrument has passed both

electrical and mechanical tests.

The consigner or carrier shall be liable for the damage to instrument resulting from

shipment. The manufacturer would not be responsible for free maintenance/rework or

replacement of the unit.

Inspect the instrument.

In case of any damage, or defect, or failure, notify your sales representative.

Check the Accessories

Please check the accessories according to the packing lists. If the accessories are

incomplete or damaged, please contact your sales representative.

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands