Scientific SMO1000A-S User Manual Download Page 176

Page: 176 / 176

User Manual SMO1000A-S

176/176

Service and Support

No user serviceable parts are inside the instrument, should it become

necessary to send back the instrument to factory for service, please

observe the following procedure.

Before dispatching the instrument please write to us giving full details of

the fault noticed, model number and serial number.

After receipt of your letter our service department will advise you whether

it is necessary to send the instrument back to us for repairs or the

adjustment is possible in your premises.

Dispatch the instrument to us (only on the receipt of our advice) at our

factory address, securely packed in original packing, duly insured and

freight paid along with accessories and a copy of the fault details noticed.

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands