Scientific SMO1000A-S User Manual Download Page 142

Page: 142 / 176

User Manual SMO1000A-S

142/176

To View the System Status

Do the following steps to view the system status:

Press the

Utility

button on the front to enter the UTILITY function menu.

Press the

System Status

softkey to view the system status of the oscilloscope. The

system status includes the information below:

Startup Times:

record the boot-strap times of the oscilloscope.

Software Version:

list the current software version of the oscilloscope.

Fpga Version:

list the current fpga version of the oscilloscope.

Hardware Version:

list the current hardware version of the oscilloscope.

Serial NO.:

list the serial number of the oscilloscope.

Scope ID:

display the scope identification of the oscilloscope.

Figure 77 System Status

Press the

Single

button on the front panel to exit.

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands