Scientific SMO1000A-S User Manual Download Page 12

Page: 12 / 176

User Manual SMO1000A-S

12/176

Measurement Category

Measurement Categories

The digital oscilloscopes can make measurements in measurement category I.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Measurement Category Definitions

Measurement category I is for measurements performed on circuits not directly connected

to MAINS. Examples are measurements on circuits not derived from MAINS, and specially

protected (internal) MAINS derived circuits. In the latter case, transient stresses are

variable; for that reason, the transient withstand capability of the equipment is made

known to the user.

Measurement category II is for measurements performed on circuits directly connected to

the low voltage installation. Examples are measurements on household appliances,

portable tools and similar equipment.

Measurement category III is for measurements performed in the building installation.

Examples are measurements on distribution boards, circuit-breakers, wiring, including

cables, bus-bars, junction boxes, switches, socket-outlets in the fixed installation, and

equipment for industrial use and some other equipment, for example. Stationary motors

with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the low-voltage

installation. Examples are electricity meters and measurements on primary over current

protection devices and ripple control units.

Working Environment

Temperature

Operating: 10

℃

to +40

℃

Non-operation:-20

℃

to +70

℃

Humidity

Under +35

℃

≤

90% relative humidity

+35

℃

to +40

℃

≤

60% relative humidity

WARNING

To avoid short circuit inside the instrument or electric shock, please do not

operate in humid environment.

Altitude

Operating: less than 3 Km

Non-operation: less than 15 Km

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands