Scientific SMO1000A-S User Manual Download Page 26

Page: 26 / 176

User Manual SMO1000A-S

26/176

Trigger

: press the button to enter the TRIGGER function menu. The oscilloscope

provides abundant advanced trigger functions

: press the button to set the trigger mode to Auto.

: press the button to set the trigger mode to

Normal.

: press the button to set the trigger mode to Single.

Trigger Level Knob

: adjust the trigger level. Turn clockwise to

increase the level and turn counterclockwise to reduce the level. During the modification,

the trigger level line would move up and down and the value in the trigger level message

box at the up-right corner of the screen would change accordingly. Press down the knob

to quickly reset the trigger level to center of the waveform.

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands