Scientific SMO1000A-S User Manual Download Page 122

Page: 122 / 176

User Manual SMO1000A-S

122/176

To Make Automatic Measurement

Perform the steps below and select voltage or time parameters to make automatic

measurement.

Press the

Measure

button on the front panel to enter the MEASURE function menu.

At the same, the frequency and period are enabled with the current trigger channel,

the statistics also was enabled.

Press the

Source

softkey, and then use the

Universal Knob

to select the desired

channel. Only analog channels (CH1 and CH2) that are displayed are available for

measurements.

To select and display measurement parameters. Press the

Type

softkey, and then

turn the

Universal Knob

to select the desired measurement parameter.

Press the

Universal Knob

to add the measurement parameter, the parameters and

value will be shown above the menu, and the statistics status will update.

To turn off the statistic function, press the

Statistics

softkey to select

Off

The measurement display area can display 5 measurement parameters at most, and the

measurements will arrange according to the selecting order. If add a sixth measurement

parameter, it will delete the first measurement.

Figure 64 Select the Measurement Parameter

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands