Scientific SMO1000A-S User Manual Download Page 66

Page: 66 / 176

User Manual SMO1000A-S

66/176

Edge Trigger

Edge trigger distinguishes the trigger points by seeking the specified edge (rising, falling,

rising & falling) and trigger level.

Press the

Setup

button on the front panel to enter the TRIGGER system function menu.

Press the

Type

softkey; turn the

Universal Knob

to set select

Edge

and then push the

knob to confirm.

Press the

Source

softkey; turn the

Universal Knob

to select

CH1

CH2

EXT

EXT/5

AC Line

as the trigger source.

Press the

Slope

softkey; turn the

Universal Knob

to select the desired trigger edge

(rising, falling or rising & falling), and then press down the knob to confirm. The current

trigger slope is displayed at the upper right corner of the screen.

Turn the

Trigger Level Knob

to adjust the trigger level to obtain stable trigger.

Figure 23 Edge Trigger

Note: Press the

Auto Setup

button will set the trigger type to Edge and slope to rising.

Summary of Contents for SMO1000A-S

















































































































































































Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands

Scientific SMO1000A-S, User Manual

Search results

Summary of Contents for SMO1000A-S

Reviews:

Related manuals for SMO1000A-S

Brands by name

Popular brands