manualshive.com logo in svg

Schmidt eZT, Operating Instructions Manual, Page: 48 / 60

Share
Download
Schmidt eZT Operating Instructions Manual Download Page 48

47

48

18. Output Data

18-1. I / O connector

Signal name

Pin number

Connector pin arrangement

-NG

1

1

2
3
4
5

6

8

9

10
11
12
13
14
15
16
17

Valid model

Description

ZTA/ZTS

eZT

High Low setpoints of comparator output.
Either signal is output depending on 
comparator judgment. 

(*1)(*4)

Output depending on set high / low 
output values. 

(*1)(*5)

Overload output.
Output when warning overload. 

(*1)

ZTA

eZT

ZTA/ZTS

eZT

Measurement-ready signal.  Output when the 
display is ready to start measurement. 

(*1)

Grand common through pin #1 to 7.

Analog output (RAW) 

(*2)

 

(*3)

Analog output (D/A) 

(*2)

 

(*3)    

Approx. +/-2v is 

output when max. force applied.

RS232C signal

N/A

ZTA/ZTS

eZT

Optional

ZTA/ZTS

eZT

ZTA/ZTS

eZT

ZTA/ZTS

eZT

Optional

OK

+NG

SC1
SC2

OVL

7

READY

OUT GND

ANALOG RAW +

ANALOG RAW -

ANALOG D/A +

ANALOG D/A -

232C_TxD

232C_RxD

232C_GND

NC
NC

18

NC

* 1  Open collector output. (Please keep source voltage less than 30V and current of 10mA.)
* 2  Please keep resistance 1k

Ω

 and more.

* 3  Differential voltage output between 2 wires.
* 4  The judgment done based on the displayed value.
* 5  Real-time value is referred for judgment at all times.

19

20

37

Input signal depending on Shift signal

EXSW1
EXSW2
EXSW3
EXSW4

Rec

Shift Input valid

Shift Input invalid

Turn on

Shut off

Same operation with ZERO button

Zero measuring displacement

Same operation with SEND button

(REVERSE)

Same operation with PEAK button

(REVERSE)

Control recording on software Force-Recorder series.

Signal name

Pin number

NC

19
20
21
22
23

25

28
29
30
31
32
33
34
35

37

Valid model

Description

Optional

N/A

Input signal
The functions differ depending on signal of 
Shift.  Refer to the bottom of the page for 
detail.  (Detect edge signal when each pin 
connected to GND pin #30.) 

(*4)

ZTA/ZTS/eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

Input grand common through pin #24 to 29 and 31.

Input mark point

Displacement input 

(*5)

Connectable linear scale and rotary encoder. 
(Corresponds to line driver output and open 
collector output.)

External power supply Grand

ZTA

eZT

ZTA/ZTS/eZT

ZTA/ZTS/eZT

NC
NC
NC
NC

EXSW2:ZERO

24

EXSW1:POWER

27

EXSW4:PEAK

26

EXSW3:SEND

Rec

Shift
GND

Mark Input

Scale A+

Scale A-(OC1)

Scale B+

Scale B- (OC2)

GND

36

External power 5V 

(*6)

+5V

* 6  Pin # 24-29 and #30 are short-circuited: ON.
* 7  Connect pin #32(A+) / #33(A-) and #34(B+) / #35(B-) in case of line driver output.
      Connect pin #33(OC1) / #35(OC2) in case of open collector output. (Keep voltage drop 0.5V and less.)
* 8  Enable to supply 5V 200mA at max.  Make sure to charge with AC adapter when supply power to external equipments.

Summary of Contents for eZT





























































Reviews:

No comments