manualshive.com logo in svg

Schmidt eZT, Operating Instructions Manual, Page: 33 / 60

Share
Download
Schmidt eZT Operating Instructions Manual Download Page 33

31

32

The peaks of the first and the second curves, instead of the peak of whole 
measurement, can be detected.
The 1st peak as [P1] and the 2nd peak as [P2] are displayed on the footer on Multi 
display.

The 1st and the 2nd peak drops (decreasing value) can be set on “1st / 2nd Peak 
Drop” of “Peak Functions” in Program Menu.  Refer to page 25.  After force value 
increases, the peak of curve is detected as the 1st (2nd) peak when the force value 
decreases by more than the set peak drops.  (See above picture)

* The set peak drop should be absolute value.

The 1st and the 2nd peaks can be detected on one direction (compression or tension).
The direction of the 2nd peak follows one of the 1st peak.

10. Peak Value

Peak is the maximum force value of measurement.

Press            (PEAK button) and [P] or [Peak] is displayed at left side of display. 

[P] and [Peak] mean Peak mode.

• In case of [OR] at Peak mode, higher peak value among compression and tensile 

peak values is displayed.

Press            (PEAK button) and peak value, measuring value, and peak value are 

displayed in order.

• In case of [AND] at Peak mode, both peak value of compression and tensile are 

displayed.  Press            (PEAK button) and compression peak, tensile peak, 

measuring value, and compression peak are displayed in order.  In case that +/- sign 

is chosen as [+/-Reverse], tensile peak, compression peak and measuring value in 

order.

11. 1st / 2nd Peak Value (ZTA, eZT only)

The 2nd peak

The 1st peak

A

A

Force

Time

The peak of curve is detected when force value  

decreases by more than the set peak drops (A).

Summary of Contents for eZT





























































Reviews:

No comments