manualshive.com logo in svg

Schmidt eZT, Operating Instructions Manual, Page: 43 / 60

Share
Download
Schmidt eZT Operating Instructions Manual Download Page 43

41

42

13. Maintenance

• Do not use any battery except BP-308.  Other battery may lead break 

down and fire.

• The date and time setting is reset when battery is disconnected.

14. Warranty

14-1. Product Warranty

We warrant the products to be free from defects in workmanship and material under 
normal use and proper maintenance for one year from original purchase.

* Please make sure to read through the included warranty for guarantee conditions.
* We cannot guarantee the products without warranty.

14-2. Pass Certificate for eZT Amplifier

eZT amplifiers are tested based on the company standards and checked under the 
environment detailed below.

* Tempe21 to 25 degrees Celsius, Humidity 30~65%RH

We do not issue certificates for passing the checks, although only the products that 
have passed those tests are shipped.

13-3. Overall Accuracy of eZT and eZ Connect load cell (eZT only)

Overall accuracy is calculated as below (e.g. eZT and eDPU-50N):

eZT and eZ Connect load cells can be used in various combination, therefore each is 
tested individually.  
The amplifier and the load cell are not calibrated (actual loading calibration) together.  
It is recommended to calibrate by yourself or with our calibration service. 
(see page 41 [13-2 Calibration and Repair] for details)

13-2. Calibration and Repair

We offer calibration service with charge.  To maintain the best accuracy and reliable 
measurement, the periodical calibration is recommended.  Please ask your local 
distributor about fee and lead time.  Please note that the function setting (Program 
Menu) and saved data may be erased when repaired.  Please make sure to send the 
force gauge with the carrying case to protect the gauge. 

13-1. Battery Change

The force gauge has rechargeable battery inside.  If the 
battery is worn out soon after charging or not charged 
at all, the battery is dying.  Please change the batteries. 
(Battery model: BP-308)  The direction is as follows.

Turn off the force gauge.  Loosen the two screws on the 
back of force gauge and remove the battery cover.  
Take the battery out and disconnect the connector. (Pull 
off the connector with tweezers and needle nose pliers.)

* Please note that the cable may get bad if force to pull the 

cable out.

Connect the connector of the new battery.  Put the new 
battery into the case and fix the battery cover with the 
screws.  Make sure to store the cable of battery inside.

=

+

eZT Amplifier

+/- 0.2%F.S. 1digit

eDPU-50N Load cell

+/- 0.2%F.S. 1digit

Overall Accuracy

+/- 0.4%F.S. 1digit

Summary of Contents for eZT





























































Reviews:

No comments