background image

Commissioning with Terminal

 

 

PR 5610 Installation Manual 

130                                                                                                                                                       Sartorius 

• 

Set the fixed span 

X to set fixed span

 

If the calibration cannot be finished correctly for any reason, press key [X]. To avoid operator errors, a 
prompt is displayed and must be replied with Yes/ No: 

[Y/N]

The system executes the command. Subsequently, the command line as shown in point 5 is displayed 
again. 

• 

Print the actual weight:  

 

 

P to Print

 

Press key [P]. The system executes the command. Subsequently, the command line as shown in point 5 
is displayed again. 

• 

Set 

the 

zero 

    

Unload and hit O

 

If necessary, zero setting (as described in point 2.) can be repeated. 

• 

Finish 

calibration 

   

E to End

 

Press key [E] 

Calculating test … 

the system calculates the test value 

Calculating test … Status OK

 

 

Subsequently, the standard command line is displayed:  

 

 Keys 

 Select item with cursor 

up

/

down

/

left

/

right C

hange with 

+

/

-

   

 Return to Fi

X

ed, Set 

F

ullscale, Calibrate by 

W

eight or 

M

illivolts 

 

E

 Exit calibration 

 

Calibration is finished. The data must be saved: Proceed as described in points 9. and 10. of  the 'Weighing point 
calibration procedure'. 

 

 

5.6.6.2  Subsequent deadload correction 

 

If the hopper weight changes e.g. due to loss (deadload reduction) or slag (deadload increase) by an amount 
which is higher than the zero set range, the automatic zero tracking and manual zero setting will not function 
any more. In these cases, subsequent deadload correction is possible, without recalibrating. 
For this, call up the weighing point calibration and set only the deadload. Calibration must be skipped.  

 

Zero correction  

Proceed as described in points 1. to 7. of the 'Weighing point calibration procedure'. This is followed by actual 
calibration: zero correction:  

 

1.  The following command line is displayed in the calibration mask:  

Unload 

 

 Calibration by weight 

 Unload and hit 

O

 or 

S

 to skip, 

 

Q

 to quit, 

E

 to end, 

X

 to set fixed span, 

P

 to print 

 

The system offers the following replies:  

Unload and hit 0

  

unload scale, set the zero 

S to skip

 

skip zero setting  

Q to quit

 

leave the calibration without doing anything 

E to end

 

calibrate and finish 

X to set fixed span

 

set the fixed span 

P to Print

 

print out the weight 

 

2.  Set the deadload 

• 

1. Unload the scale 

• 

2. Press key [0] 

• 

The instrument evaluates the data. The following command line is displayed in the calibration mask:  

Setting deadloads … 

 

 

s

ystem saves the data, subsequently:  

Setting deadloads … Status OK 

message is displayed during approx. 2 sec. The weight display goes to: 
0000 kg 

• 

In case of error, repeat zero setting. See point 3 

 

Summary of Contents for PR 5610






































































































































































Reviews: