Samsung XRN-1610S User Manual Download

Page: 38 / 82

Connecting the iSCSI

If you connect the NVR with an iSCSI device, you can search, connect and disconnect the iSCSI device.

•

iSCSI Usable Name : It displays the name of iSCSI in compliance with the iSCSI protocol format.

•

Capacity : It displays the currently used amount/total capacity of iSCSI devices.

•

Status : Displays the status of an installed iSCSI device.

List of products supported

Promise Technology vessRAID 1740i / 1840i / 2600i 1ea JBOD 3ea

Adding an iSCSI device automatically

In the iSCSI window, click on the <

Add Automatically

> button.

On the Auto Add screen, enter the IP address and the connecting port, and click <

In the <

iSCSI usable name

> list, click on a device to add.

After entering ID/password, click on the <

> button.

Adding an iSCSI device manually

On the iSCSI screen, click <

Add manually

On the Manual Add screen, enter the IP address, the connecting port, the ID and the password, and click

Canceling registration of iSCSI devices

In the <

iSCSI usable name

> list, select an iSCSI device to delete.

Click on the <

Delete

> button to launch the Delete window.

If you click <

>, the iSCSI device is removed from the list.

For iSCSI equipment, use network port 2.

When using a hub to connect an iSCSI device with NVR, make sure to use the GIGA hub and to use an independent network

to save data normally.

When you perform single directional CHAP authentication in vers. RAID, an iSCSI device in compliance with the NVR, you

need to use the iSCSI Manual Add function to make a connection to iSCSI.

If multiple NVRs try to access a single iSCSI device, it can cause a problem.

When the NVR is connected to an iSCSI device, if you change the iSCSI equipment setting, a problem can occur.

A HDD to be mounted in vess RAID should be listed in the RAID compatibility list.

It is recommended that you configure each volume for an iSCSi device with a maximum of 16 HDD.

When you register an iSCSI device in the NVR for the first time, you need to format it first.

The iSCSI lun mapping function is supported.

If you activate the lun mapping function in the iSCSI device, the lun can only be connected to an NVR which is mapped.

38_

menu setup

Summary of Contents for XRN-1610S



















































































Search results

Summary of Contents for XRN-1610S

Reviews:

Related manuals for XRN-1610S

Brands by name

Popular brands

Samsung XRN-1610S, User Manual

Search results

Summary of Contents for XRN-1610S

Reviews:

Related manuals for XRN-1610S

Brands by name

Popular brands