Samsung XRN-1610S User Manual Download

Page: 35 / 82

Setup

In the bottom of the camera setting screen, press the <

Setup

> button to set your camera while watching the

live video of the selected camera.

SUNAPI (Samsung Unified Network API) : Camera that supports the communication protocols provided by Hanwha Techwin

1. Camera supporting SUNAPI.

2. A camera connected with admin privileges.

3. A camera connected to Samsung protocols.

In the above cases, you can use the function.

For more details on camera settings, refer to the camera user manual.

Settings and operational spec vary depending on each camera.

This function is not supported in some models.

SSDR

If there is a significant difference between the dark and the bright areas, increase the brightness of the dark

areas to maintain the level of brightness of the entire area.

Mode, level, D-Range can be set.

Backlight

You can view both bright and dark areas.

Mode, WDR level, WDR black/white levels can be set.

exposure

You can adjust the exposure of your camera.

Brightness control, shutter, SSNR, Sens-up,

IRIS/lens

, and

AGC

can be set.

Day/night

You can change the mode to adjust the color and contrast.

Mode, switching time, brightness change, alarm time, alarm input/output, negative color, daytime/nighttime

switching and simple focus, and activation time can be set.

Special

DIS (shaking compensation), use of Defog levels can be set.

Focus

You can adjust the focus of you camera's video.

Items of Simple Focus and Focus-Initialize Setting can be set.

Flip

Mirror and flip modes can be set.

After finishing with setting camera, click on the <

> button to move back to the previous screen.

Dewarping Setup

Press <

Dewarping Setup

> at the bottom of the camera settings screen and a distortion correction settings

window for each channel is prompted.

•

Profile/View type : You can select the view type of profiles, except for fixed profiles (SourceMJPEG,

SourceH264, DewarpMJPEG, DewarpH264) whose settings can't be changed, in the profile list on the

distortion correction settings pop-up window.

•

Mounting mode : You can change the fisheye installation type. You can select a view mode from among

CEILING/

FLOOR

/WALL depending on the installation location.

•

View : You can change the fisheye view mode of the current screen according to each split section.

If there is no camera registered in the NVR that supports fisheye view, <

Dewarping Setup

> will not be available.

Dewarping Setup

CH6

The camera may be rebooted when changing the mounting mode.

Profile

Live4NVR

Rec4NVR

MOBILE

View type

Dewarp View

Source View

Mounting mode

Ground

View

Quad View

Cancel

English

_35

●

menu setup

Summary of Contents for XRN-1610S



















































































Search results

Summary of Contents for XRN-1610S

Reviews:

Related manuals for XRN-1610S

Brands by name

Popular brands

Samsung XRN-1610S, User Manual

Search results

Summary of Contents for XRN-1610S

Reviews:

Related manuals for XRN-1610S

Brands by name

Popular brands