Samsung KS8910 User Manual Download Page 11 | Manualshive

Page: 11 / 99

background image

PRODUCT OVERVIEW

KS8910 100/10 Mbps ETHERNET TRANSCEIVER

1-2

Preliminary Spec. ver

1.4

FEATURES

•

Support for old and new media : Compatible with existing 10-Mbit/s networks.

•

10BASE-T/100-BASE-TX operation : Range of price/performance points, Phased Conversion

•

Full IEEE 802.3 compatibility : Compatible with existing hardware and software.

•

Standard CSMA/CD,Full duplex capability at 10 and 100 Mbit/s : Increase in data throughput performance.

•

Power management : Reduces power dissipation

•

CMOS process with Single 3.3 volt operating supply : Compatible with standard system power supplies.

•

On-chip filtering : Providing integrated lower cost solution

•

Manual or automatic negotiation of port configuration : Provides ease of use in a mixed 10/100 Mbit/s network
configuration

•

MII compliant interface : Can be used with many 100Base-TX MACs.

•

Built-in transmit and receive filtering for 10BASE-T and 100BASE-TX

•

Built-in LED drivers

ETHERNET SYSTEM BLOCK DIAGRAM

The complete Ethernet subsystem shown in Figure 1-2 is divided into three sections:

•

The system bus interface and Direct Memory Access (DMA) engine

•

The Media Access Control (MAC) layer

•

The Physical or Medium Dependent Interface (MDI) layer

The PCI bus interface section contains transmit and receive data buffering, DMA control buffering, and a register
access module buffering.

The MAC layer consists of transmit and receive blocks, a Content Addressable Memory (CAM) for address
recognition, along with control, status, and error counter registers.

This representative PCI-based 100/10-Mbit/s Ethernet controller supports the Media Independent Interface (MII).
The MII is a standard for a media-independent layer which separates physical-layer issues from the MAC layer.
The MII is part of the ISO approved IEEE 802.3 100-Base-T standard for 100 Mbit/s Ethernet.

This specification describes a single chip which implements a Physical or MDI layer capable of accepting 100/10
Mbit/s Ethernet signals that provides a Media Independent Interface (MII) for connectivity to the MAC layer. It is
intended as an interface specification and an architectural overview of the device and its operation.

«
...
9
10
11
12
13
...
»

Summary of Contents for KS8910




































































































Reviews:

No comments

Related manuals for KS8910

Brand: Nautel Pages: 4

Brand: Intempco Pages: 2

EWFS Plug receiver PL

Brand: WAREMA Pages: 6

Brand: AMG Pages: 12

Brand: Listen Pages: 2

Brand: Yaesu Pages: 44

Brand: Omega Pages: 20

Brand: Kathrein Pages: 36

PEP2000 - UPDATE V0150 AND V11.53

Brand: Yaesu Pages: 8

Brand: Televes Pages: 64

Brand: Jonsa Pages: 12

Brand: Harman Kardon Pages: 12

Brand: Icom Pages: 32

Brand: Camille Bauer Pages: 14

Brand: Gonset Pages: 23

Brand: Procare Pages: 2

Brand: Sachtler Pages: 12

EXTA LIFE RNP-21

Brand: Zamel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands