Samsung CLX-9350ND Service Manual Download

Page: 463 / 549

7. Troubles

●

Code :

S3-3211

●

Error message :

Scan System Failure

●

Symptom / Cause :

At system booting, the MFP could not detect the DAD

DADF could not detect the paper. ( The green LED of

●

Troubleshooting method :

1. Reboot the MFP.

Check the initial operation of DADF (whether the m

2. Is power supplied to the DADF board?

Check the LED on the DADF board.

3. Check the connection between DADF board and Sc

Is it connected properly?

Yes : Replace the DADF board.

DADF board

4. Is power supplied to the Scan board?

Check the LED on the Scan board.

5. Check the connection between Scanner and Main b

If the connection is OK, replace the Scanner board.

●

Replacement part

- JC92-02170A : PBA-SCAN

- JC92-02165A : PBA-ADF

Service Manual
CLX-9250/9350 series

7-1

shooting

e #S3-3211 : Turn off then on.

DADF external is off. )

otor is working or not)

can board.

Scanner board

board.

SAMSUNG ELECTRONICS

Summary of Contents for CLX-9350ND






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9350ND

Reviews:

Related manuals for CLX-9350ND

Brands by name

Popular brands

Samsung CLX-9350ND, Service Manual

Search results

Summary of Contents for CLX-9350ND

Reviews:

Related manuals for CLX-9350ND

Brands by name

Popular brands