Samsung CLX-9350ND Service Manual Download

Page: 450 / 549

7. Troubles

●

Code :

S1-5521

●

Error message :

FDI device is not ins

●

Symptom / Cause :

The MFP could not detect the FDI device

●

Troubleshooting method :

1. Was the FDI device removed after installation?

Yes : Select “FDI device uninstall” on UI menu.

2. Did you replace the HDD / Video board / FDI device

Yes : Update the firmware for the new board.

3. Does the problem occur after updating the firmware

Yes :

A. Print the configuration report and check the fir

B. If all software versions are not normal, update

C If th

i t

th d f

C. If the problem persists, replace the defective d

4. Check the connection between FDI device and Vide

Remove the FDI device and re-install it.

5. Replace the FDI device

6. If the problem persists, replace the Video board.

[ FD I Dev

●

Replacement part

- JC92-01616A : PBA SUB-FDI

- JC92-02150A : PBA-MAIN (CLX-9350ND)

- JC92-02235A : PBA-MAIN (CLX-9250ND)

Service Manual
CLX-9250/9350 series

7-1

- JC92-02235A : PBA-MAIN (CLX-9250ND)

shooting

stalled. Install the device.

rmware version.

e the firmware again.

(HDD

Vid

FDI d

)

device. (HDD or Video board or FDI device)

eo board.

vice ]

SAMSUNG ELECTRONICS

Summary of Contents for CLX-9350ND






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9350ND

Reviews:

Related manuals for CLX-9350ND

Brands by name

Popular brands

Samsung CLX-9350ND, Service Manual

Search results

Summary of Contents for CLX-9350ND

Reviews:

Related manuals for CLX-9350ND

Brands by name

Popular brands