saia-burgess PCD7.D23 Series Manual Download Page 27

Page: 27 / 59

Saia-Burgess

Controls Ltd.

Manual PCD7.D23x│Document 26/795; Edition E7│15.04.2005

Software

4-1

Basic commands

Software

The terminal interface can be in different operation modes:

●

Direct mode:

The direct mode is the default full duplex mode with key code directly sent if the

buttons on the PCD7.D231 or PCD7.D232 are pushed or the rotary wheel as-

sembly on the PCD7.D230 is used.

Commands go unconﬁrmed (no handshake).

●

Setup menu mode:

If at power-up an arbitrary key (except the switch key) is kept pushes the dis-

play enters in the setup menu mode with built-in menu browser.

No key code is sent. No commands are received.

This mode is used to set the communication and contrast settings.

At the PCD7.D231 and PCD7.D232 this mode can also be entered using the

Info key at run time.

●

Free Terminal Protocol FTP mode:

The Free Terminal Protocol FTP mode is an alternative half duplex mode with

key codes buffered. The last entered push buttons or turns / pushes on the

rotary wheel assembly are returned at request (poll) if the terminal is set to ac-

tive before. This is used for half duplex RS-485.

Selection goes over the setup menu.

●

Serial Data/Setup protocol:

The serial data/setup mode is an alternative full duplex mode with conﬁrmed

command sending (handshake). In this mode, key code sending is inhibited.

Switching from the direct mode (no handshake, keys active) to the serial data/

setup mode (handshake, no keys sent) and vice-versa is done by serial com-

mands.

The PCD7.D23x may also be in a special alarm indicating mode if internal testing did

not pass. In this case contact SBC.

4.1

Basic commands

4.1.1 The PCD7.D23x return codes in direct mode

Compatibility

PCD7.

D1x0

D202

D232

D231

D230

dec. hex. Meaning

stand.

Fkeys

down arrow

down

right arrow

Turn right

right

left arrow

Turn left

left

up arrow

2nd long

2nd escape

Enter

Push short

enter

esc

Push long

escape

Autorepeat

started

Autorepeat

started

Long turn on

Repeat on

Summary of Contents for PCD7.D23 Series




























































Search results

Summary of Contents for PCD7.D23 Series

Reviews:

Related manuals for PCD7.D23 Series

Brands by name

Popular brands

saia-burgess PCD7.D23 Series, Manual

Search results

Summary of Contents for PCD7.D23 Series

Reviews:

Related manuals for PCD7.D23 Series

Brands by name

Popular brands