6
Protective gloves must be worn at all times during maintenance and
cleaning work.
Pos: 13.9.11 /Inne nteil/Sicherheitsvorschriften/Wa rtung und Lage rung/Betrieb sstoffe - Schutzausrüstung/Date nblä tter (Moto röl+Kraftstoff) @ 64\mod_1579858529841_6.docx @ 625402 @ @ 1
•
When handling operating fluids, such as engine oil and fuel, suitable protective
equipment (e.g. suitable protective gloves) must be worn.
The data sheets of the operating fluids must be observed.
Pos: 13.9.12 /Inne nteil/Sicherheitsvorschriften/Wa rtung und Lage rung/Zündkerzenstecker a bziehe n Mäher @ 25\mod _1377160770344_6.do cx @ 187054 @ @ 1
Maintenance and cleaning work may only be carried out on level surfaces
with the engine switched off and the spark plug connector disconnected.
Regular maintenance is essential for safety and top performance.
Pos: 13.9.13 /Inne nteil/Sicherheitsvorschriften/Wa rtung und Lage rung/Kerzenstecke r niema ls bei laufendem Mo tor ab ziehen @ 13\mod _1280219056956_6.do cx @ 110073 @ @ 1
•
Never remove the plug connector when the engine is running!
Risk of electric shock.
Pos: 13.9.14 /Inne nteil/Sicherheitsvorschriften/Ha ndhab ung/Kerzenste cker nur be i abgekühltem Moto r abziehen @ 53\mod_1513001243580_6.do cx @ 577230 @ @ 1
•
Only remove the plug connector once the engine has cooled down.
Risk of burns!
Pos: 13.9.15 /Inne nteil/Sicherheitsvorschriften/Wa rtung und Lage rung/Auf fe sten Sitz des Zündke rze nstecke rs a chten @ 53\mod _1513003523258_6.do cx @ 577258 @ @ 1
•
Make sure the spark plug connector is fitted tightly. Risk of electric shock.
Pos: 13.9.16 /Inne nteil/Sicherheitsvorschriften/Wa rtung und Lage rung/Tank nur im Fre ien entleeren @ 0\mod_1115186486750_6.docx @ 267 @ @ 1
•
If the tank has to be emptied, this should be done in the open, and with a cold
engine. Take care to ensure that no fuel is spilt.
Pos: 13.9.17 /Inne nteil/Sicherheitsvorschriften/Wa rtung und Lage rung/Nur Originalersatzteile ve rwenden SABO+JD @ 26\mod_1377168488208_6. docx @ 187531 @ @ 1
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
Pos: 14.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_6.do cx @ 41 @ @ 1
Pos: 14.2 /Innente il/Be schreib ung de r Ba uteile/1 BESCHREIBUNG DER BAUT EILE @ 0\mo d_1115187892468_6. docx @ 271 @ 1 @ 1
7 DESCRIPTION OF COMPONENTS
Pos: 14.3 /Innente il/Be schreib ung de r Ba uteile/ Bild JS63 VARIO C SA222119 @ 63\mod_1574693196843_0. docx @ 621781 @ @ 1
Pos: 14.4 /Innente il/Be schreib ung de r Ba uteile/ Beschre ibung der Baute ile JS63 VAR IO/C/JS63V/C SA1721 Tex t @ 66\mo d_1594638484432_6. docx @ 635508 @ @ 1
1 Engine stop safety control bar
2 Vario actuation
3 Drive control bar
4 Tank cap
5 Engine cover
6 Air filter
7 Spark plug
8 Exhaust protection grill
9 Belt drive covers
10 Splash guard
11 Bar height adjustment
12 Oil filling nozzle with dipstick
13 Starter cable grip
Pos: 15.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_6.do cx @ 41 @ @ 1
Pos: 15.2 /Innente il/Vo rbe reitende Arbeiten/1 VOR BEREITENDE AR BEITEN @ 0\mod_1115194917734_6.docx @ 291 @ 1 @ 1
8 PREPARATION
Pos: 15.3 /Innente il/Vo rbe reitende Arbeiten/Vo rbe reitende Arbeite n Text 53-PR O M VARIO SABO+JD @ 43\mod _1464162544375_6.do cx @ 497696 @ @ 1
The following parts are included in the packaging for assembly of the mower:
•
Mower with preassembled guide bar
•
Tool bag with the following contents:
–
Operating instructions with declaration of conformity
–
Warranty conditions (depending on model)
–
Various fixing parts.
In the unlikely event of a missing part, please contact your dealer.
Pos: 15.4 /Innente il/Vo rbe reitende Arbeiten/Vo r Monta ge... Holm und... Sta rterseilhalte r... Zündke rzenstecke r abziehen! H inweis @ 32\mod _1408441229475_6.do cx @ 239121 @ @ 1
ATTENTION
Always remove the spark plug connector before fitting the bar and starter cable
holder, and when folding the bar out. Following assembly, at the latest before
starting the engine, push the spark plug connector back in place.
Pos: 15.5 /Innente il/Vo rbe reitende Arbeiten/1.1 Führungsho lm hochste llen ( Abbildung A1 + E1 + B1) @ 0\mod_1125644224779_6.docx @ 951 @ 2 @ 1
Raise the guide bar (figure A1 + E1 + B1 )
Pos: 15.6 /Innente il/Vo rbe reitende Arbeiten/Führung sholm hochstelle n Text JS63 Hinweis @ 3\mo d_1158738822149_6. docx @ 20192 @ @ 1
IMPORTANT:
Ensure that the Bowden cables are not kinked or trapped when raising the
guide bars!
Pos: 15.7 /Innente il/Vo rbe reitende Arbeiten/Kabel nicht knicken ode r einkle mmen W ICHTIG @ 58\mod_1567149392984_6.docx @ 604682 @ @ 1
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the guide bars are folded apart or collapsed! Always run the cables along
the outside of the bar connection. A damaged cable may result in a technical
defect of the device.
Pos: 15.8 /Innente il/Vo rbe reitende Arbeiten/Führung sholm hochstelle n Text JS63 @ 3\mod _1158732190694_6.d ocx @ 20182 @ @ 1
–
Carefully take the mower out of the shipping box.
–
Remove the wing nut (B) and the saucer-head screw (D) on both sides
A1
.
–
Open out the Z-shaped folded guide bar by pulling upwards.
–
Lift the upper guide bar section until upper and lower section of the guide bar are
at one level.
(Figure E1)
–
The quick-release clamps for attachment of the upper and lower section of the bar
are preset by the manufacturer.
1. Pull up the quick-release clamp to the bar.
2. Tighten the screws by hand.
3. Open the quick-release clamp.
4. Tighten the screw by 1/4 to 1/2 turn.
5. Pull up the quick-release clamp again and check whether the bars are firmly
connected. Correct if necessary.
–
Keep this setting. If the connection becomes loose over time, the screws
must be tightened.
–
Carefully pull back the guide bars and align the bore in the lower bar section with
the desired height adjustment opening in the holder (C)
B1
.
Three different handlebar heights can be set.
–
Plug the screw (D) from the outside on both sides through the holder and lower bar
section, and tighten it to the knurled nut (B). Use the same opening in the
holder (C) on both sides
B1
.
–
Attach the Bowden cables to the lower bar with the help of cable ties from
the tool bag.
Pos: 15.9 /Innente il/Vo rbe reitende Arbeiten/Holm höhenve rstellung ...Umschlagen des Holms Hinweis JS63 @ 14\mod_1285845829023_6.docx @ 119259 @ @ 1
CAUTION
When operating the bar height adjustment, the bar may turn over
unintentionally when loosening the wing nuts (B) B1 and the attachment
screws (D) between the lower bar section and the holder. In addition, this
may result in crushed points between the bottom of the bar and the holder.
This may result in risk of injury.
Pos: 15.10 / Innenteil/ Vorbe reitende Arbe iten/1.1 Holmstart-Montage ( Abbildung L1 ) @ 0\mod_1127986352485_6. docx @ 1414 @ 2 @ 1
Handle starter assembly (figure L1 )
Pos: 15.11 / Innenteil/ Vorbe reitende Arbe iten/Montage Starte rse ilhalter Text Mo torbrem se @ 37\mod _1436190239176_6.do cx @ 399706 @ @ 1
–
Remove the starter cable holder (1) from the tool bag.
–
Unscrew the nut until the two halves can be pushed over the bar.
–
There is a sticker (2) on the top bar showing the position of the starter
cable holder.
ATTENTION
For reasons of safety, the starter cable holder may only be fitted
in the prescribed position.
–
Press the engine stop control bar (3) onto the upper bar section (4) and hold it
there; pull out the starter cable (5) and insert it into the starter cable holder.
–
Fit the two halves together (6), re-tighten the nut. This prevents the starter cable
from popping out.
The starter cable holder must be fitted / aligned in such a way that the starter cable
is freely accessible and does not rub against any other parts.
Pos: 15.12 / Innenteil/ Vorbe reitende Arbe iten/1.1 Vo rderräde r verriegeln und entriegeln (JS63 VAR IO C, JS63VC) (Abbildung T3 ) @ 66\mo d_1594639142094_6. docx @ 635592 @ 2 @ 1
Pos: 15.15 / Innenteil/ Vorbe reitende Arbe iten/1.1 Schnitthöhe e instellen @ 4\mod_1159264261106_6.docx @ 21022 @ 2 @ 1
Adjusting the cutting height
Pos: 15.16 / Innenteil/ Sicherhe itshinweise/Sicherheitshinweis: Messe r, Moto rStop @ 0\mod _1115201376187_6.d ocx @ 339 @ @ 1
Safety information!
For explanation of symbols, see the table on page 3
Pos: 15.17 / Innenteil/ Vorbe reitende Arbe iten/Einste llung der Vorderradhö he Text JS63 VARIO/C/JS63V/C @ 66\mod_1594639351237_6. docx @ 635621 @ @ 1
Front wheel height adjustment
By means of a height adjustment lever at the left front wheel, both front wheels
can be set.
–
Set the height adjustment lever to the desired position.
Pos: 15.18 / Innenteil/ Vorbe reitende Arbe iten/Einste llung der H inte rra dhöhe Text J S63 @ 3\mod_1158746223338_6.docx @ 20282 @ @ 1
Rear wheel height adjustment (figure V3 )
By means of a height adjustment lever at the left rear wheel, both rear wheels
can be set.
–
Slightly lift the device by hand at the lower bar to unload the wheel.