Sabo 43-EL COMPACT, Operator'S Manual

Page: 34 / 72

8
Tips on caring for your lawn (Illustration M )
WARNING
Remove any objects (stones, wood, branches, etc.) from the lawn before each
cut; but still watch out for objects lying around during the mowing process.
Ask your dealer about lawn care instructions. Information and instructions about
mowing can also be found on the manufacturer website.
15 SERVICE INTERVALS
IMPORTANT
Avoid damage! Under extreme or unusual conditions, shorter servicing intervals
than the ones specified below may be necessary. If you establish any problems,
please contact an authorised workshop.
Carry out routine servicing on the machine in line with the following servicing intervals.
Work must be carried out at the following servicing intervals in addition to the
maintenance work listed in these operating instructions.
Before initial use
• Check all screw connections for a tight fit.
• Check the cutting blade screw and have an authorised workshop tighten it if
necessary.
• Check whether the safety control bar for the engine brake is working perfectly.
• Check that all protective devices have been attached properly and are not
damaged.
Before every operation
• Check the lawn area and remove any objects.
• Check the area of the boundary wires (if an automatic mower is being used for
lawn care).
• Check the condition and firm fit of the blade, if necessary have an authorised
workshop tighten the blade screw.
• Check whether the safety control bar for the engine brake is working perfectly.
• Check that all protective devices have been attached properly and are not
damaged.
• Check grass collecting equipment for wear or loss of functionality.
• Check the upper part of the bar (insulation) for damage.
• Check the connection cable for damage and ageing.
Every 10 operating hours
• Check all screw connections for a tight fit.
• Check the fan, blade coupling and fan housing regularly for wear and a tight fit.
After every operation
• Clean the mower.
• Check the blade for damage and wear.
Every 15-20 operating hours or annually
• Lubricate the wheel bearings.
16 CARE AND SERVICING OF YOUR LAWNMOWER
Regular care is the best way to guarantee a long service life and problem-free
operation. Insufficient equipment maintenance will lead to safety-related faults!
Only use original spare parts because only those guarantee safety and quality!
Safety instruction!
See table for explanation of symbols
page 3
Cleaning (Illustration O )
Remove dirt and grass residue immediately after finishing mowing. Place the mower on
its side and use a brush or cloth to clean.
ATTENTION
Do not put your fingers into the openings of the fan housing and hold onto the
fan. If the blade bar is rotated during cleaning, there is a risk that your fingers
may become caught between the fan and the fan housing!
IMPORTANT
Never spray the mower with water. This may damage the electrical systems.
Storage
Always keep the machine in a clean condition in a closed, dry room out of reach of
children. Always allow the engine to cool down before you store the machine in a
closed room.
Collapsing the handle (Illustration A1 )
– To save storage space or for transportation, loosen the four wing nuts so that the
guide tube can be folded together without resistance in a Z-shape above the
engine
A1 .
The toothed plastic adaptations on the bottom bar end must snap out of the
cut-out on the housing.
– Do not kink nor squeeze the cable in the process.
CAUTION
When folding the bar for transport and storage purposes, when loosening the
wing nuts and snapping the toothed plastic adaptations from the cut-out on the
housing, it is possible that unintentional upsetting of the bar may occur. In
addition, this may result in crushed points between the top and bottom part of
the bar as well as the housing. This may result in a risk of injury!
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the handlebars are folded apart or collapsed! Always run the cables along
the outside of the bar connection. A damaged cable may result in a technical
defect of the equipment.
Transporting and securing the equipment (Illustration N )
– If the equipment has to be carried, do not hold the ejection flap! Hold the carrying
handle at the front and at the back (see Figure N ).
Please take the weight of the machine into consideration before lifting it (see
Technical Data). Lifting large weights can result in health problems.
We recommend that two people should always lift or carry the equipment.
– Transport the unit upright on all 4 wheels to avoid damage to the equipment and
personal injury.
– Park the means of transport on level ground so that the equipment cannot roll
away before it is secured.
– Remove the collecting bag and secure it separately during transport.
– Secure the equipment with approved load-securing devices (e.g. tie-down straps
with clamping elements) on or inside the vehicle. Tie-down straps are belt bands
made of synthetic fibres. Every tie-down strap is marked with a label. The label
contains important details for application. The information on this label must be
heeded when using the tie-down strap.
– For loaded goods that can roll, we recommend using direct strapping with four
lashing straps. Secure the wheels of the equipment in such a way that it does not
move during transportation.
NOTE
Do not tighten the belts too firmly. Fixing the equipment too firmly can cause
damage.
Maintenance of the blade
A sharp blade guarantees optimum cutting performance. Before you start mowing,
always check the condition and firm attachment of the cutting blade. The blade
attachment screw must always be tightened by an authorised workshop. If the blade
screw is too tight or too loose, the blade coupling and cutter bar can become damaged
or loose which can lead to serious injuries. A worn or damaged blade must always be
replaced.
Sharpening and balancing the blade (Illustration Q )
WARNING
The sharpening and balancing of the blade should be carried out only by an
authorized specialist workshop, since according to the applicable standard DIN
EN 60335, an insulation test must always be carried out following repairs or
maintenance work to insulating components (e.g. blade screws).
An improperly sharpened or unbalanced blade can cause severe vibrations, and
damage the lawnmower.
The cutting edges of the cutting blade may be grinded only until the respective value
(see illustration
Q ) or the marking (1) on the cutting blade (ring) has been reached.
Attention! Observe the grinding angle of 30°.
Your professional workshop can check this value - (grinding limit) for you!
WARNING
A blade by which the wear limit (marking) has been exceeded can break off and
spin away; this can cause severe injuries.