Ross CrossOver 16, Operator'S Manual

Page: 72 / 92

6–6 • Memories, USB Storage, and Upgrades CrossOver 16 User Manual (v4.0)
› Input 3 is not recalled to the Program bus
(on-air image is not affected).
› Input 4 is not recalled to Key 1 as Key 1 is
on-air (on-air image is not affected).
› Input 5 is recalled to Key 2 (on-air image is not
affected as Key 2 is off-air).
• Scenario 2
› Input 2 is recalled to the Preset bus.
› Input 3 is not recalled to the Program bus
(on-air image is not affected).
› Input 4 is recalled to Key 1 (on-air image is not
affected as Key 1 is off-air).
› Input 5 is recalled to Key 2 (on-air image is not
affected as Key 2 is off-air).
Recall Mode: MemAI (Memory AI)
• Scenario 1
› Input 3 is recalled to the Preset bus (on-air
image is not affected).
› Input 4 is recalled to Key 2 as Key 1 is on-air
(on-air image is not affected).
› Input 5 is recalled to Key 3 as Key 2 is now
in-use (on-air image is not affected).
› Next Transition area is set to transition
background, Key 1 and Key 2.
• Scenario 2
› Input 3 is recalled to the Preset bus (on-air
image is not affected).
› Input 4 is recalled to Key 1 (on-air image is not
affected).
› Input 5 is recalled to Key 2 (on-air image is not
affected).
› Next Transition area is set to transition
background, Key 1, and Key 2.
Recall Mode: DVEDis (DVE Dissolve)
• Scenario 1
› Only the DVE parameters of Key 1 are recalled
and the switcher performs a smooth effects
dissolve between the current DVE parameters
and the DVE parameters stored in the memory.
No other properties are recalled.
• Scenario 2 has the same behavior has Scenario 1.
Recall Mode: EffDis (Effects Dissolve)
• Scenario 1
› Input 2 is recalled to the Preset bus.
› Input 3 is recalled to the Program bus (on-air
image dissolves to Input 3).
› Input 4 is recalled to Key 1 (on-air image
dissolves to Input 4 and slews to new location).
› Input 5 is recalled to Key 2 (on-air image not
affected as Key 2 is off-air).
• Scenario 2 has the same behavior has Scenario 1.
To set the Recall mode:
1. Press RECALL .
2.
Press
NEXT
until
Attrib
is displayed.
3.
Use the
Attrib
knob to select
Recall Mode
.
4. Use the Value knob to select the Memory
Recall mode. You can choose from the
following:
• PGM — Program mode.
• PV — Recall to Preview mode.
• MemAI — Memory AI mode.
• EffDiss — Effects Dissolve mode.
• Memory — The Memory Recall mode
stored in the memory register being recalled
is used.
5. If you are using the EffDiss Memory Recall
mode, set the desired transition time as follows:
• Use the Attrib knob to select EffDur.
• Use the Value knob to select the duration
of the Effects Dissolve transition.
USB Storage
You can use a USB drive to:
• Save and load sets of memory registers,
personality, and installation settings to and from a
USB drive
• Perform software upgrades
These files and settings can be copied from the USB
drive and backed-up on your computer.
Note:
• If you are transferring large files to the USB drive
via the FTP interface, do not perform any other
tasks that require the USB drive until the transfer
has finished.
• Wait 5 seconds after inserting a USB drive into the
USB port before using it.
For More Information on...
• performing software upgrades, refer to the section
“Software Upgrades” on page 6-7.
• FTP access to the USB drive, refer to the section
“Creating an FTP Connection” on page 4-6.
RECALL
NEXT