manualshive.com logo in svg

Rosemount 8732 Series, Reference Manual

Share
Download
Rosemount 8732 Series Reference Manual Download Page 97

Reference Manual 

00809-0100-4663, Rev BA 
January 2010

B-5

Rosemount 8732

HAZARDOUS LOCATION 
CERTIFICATIONS

Equivalent Hazardous Location Certifications for sensor and transmitter must 
match in integrally-mounted magnetic flowmeter systems. Remote-mounted 
systems do not require matched hazardous location certification option codes.

Transmitter Approval 
Information

Table B-5.  Transmitter Option 
Codes

Equipment Category 1 - Dust Environment

Dust Environment Only

Trans: Dust Ignition Proof

NF

-

NF

Other Certifications

Product Certification Code

(3)

European Pressure Equipment 
Directive (PED)

PD

-

PD

NSF 61 Drinking Water

(4)

DW

-

DW

(1) Available in remote mount configuration only. Requires equivalent ATEX approval on the sensor
(2) For I.S. Output, Output Code B must be ordered
(3) Product Certification Codes are added to the Sensor model number only
(4) Only available with PTFE (all line sizes) or Polyurethane (4 in. or larger) Lining Materials and 

316L SST Electrodes

Rosemount 

8732E

Rosemount 

8712D

Rosemount 

8712H

Approval Codes

HART

F

OUNDATION

 

fieldbus

NA

•

•

•

N0

•

•

•

•

N1

•

•

•

N5

•

•

•

•

N7

•

•

ND

•

•

NF

•

•

E1

•

•

E5

•

•

E7

•

•

ED

•

•

Summary of Contents for 8732 Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands