Rosemount 8732 Series Reference Manual Download Page 148

Page: 148 / 190

Reference Manual

00809-0100-4663, Rev BA

January 2010

Rosemount 8732

E-8

ENDRESS AND HAUSER
SENSORS

Connect coil drive and electrode cables as shown in Figure E-5.

Endress and Hauser
Sensor to
Rosemount 8732
Transmitter

Figure E-5. Wiring Diagram for
Endress and Hauser Sensors
and Rosemount 8732

Table E-6. Endress and Hauser
Sensor Wiring Connections

Electrodes

Coils

ROSEMOUNT 8732

TRANSMITTER

ENDRESS AND HAUSER

SENSORS

Rosemount 8732

Endress and Hauser Sensors

This is a pulsed DC magnetic flowmeter.

Do not connect AC power

to the sensor

or to terminals 1 and 2 of the
transmitter

, or replacement of the

electronics board will be necessary.

Summary of Contents for 8732 Series































































































































































































Search results

Summary of Contents for 8732 Series

Reviews:

Brands by name

Popular brands

Rosemount 8732 Series, Reference Manual

Search results

Summary of Contents for 8732 Series

Reviews:

Brands by name

Popular brands