manualshive.com logo in svg

Rosemount 8732 Series, Reference Manual

Share
Download
Rosemount 8732 Series Reference Manual Download Page 55

Reference Manual 

00809-0100-4663, Rev BA
January 2010

4-17

Rosemount 8732

Electrode Type 

Electrode type enables you to select the electrode type for your magnetic 
transmitter system. This variable only needs to be changed if you have 
replaced electrodes or if you have replaced your sensor. Options for this value 
are:

•

Standard

•

Std & Ground

•

Bullet

•

Other

Electrode Material 

Electrode Material enables you to select the electrode material for your 
magnetic transmitter system. This variable only needs to be changed if you 
have replaced electrodes or if you have replaced your sensor. Options for this 
value are:

•

316L SST

•

Nickel Alloy 276 (UNS N10276)

•

Tantalum

•

Titanium 

•

80% Platinum – 20% Iridium

•

Alloy 20

•

Other

Liner Material 

Liner material enables you to select the liner material for the attached sensor. 
This variable only needs to be changed if you have replaced your sensor. 
Options for this value are:

•

PTFE

•

ETFE

•

PFA

•

Polyurethane

•

Linatex

•

Natural Rubber

•

Neoprene

•

Other

MODE

Set and review the mode configuration for the transducer function block.

375 Transducer Block, Detailed Setup, Device Info, Construction Materials

375 Transducer Block, Detailed Setup, Device Info, Construction Materials

375 Transducer Block, Detailed Setup, Device Info, Construction Materials

375

Transducer Block

Summary of Contents for 8732 Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands