manualshive.com logo in svg

Rosemount 8732 Series, Reference Manual

Share
Download
Rosemount 8732 Series Reference Manual Download Page 47

Reference Manual 

00809-0100-4663, Rev BA
January 2010

4-9

Rosemount 8732

8714i Result 

Displays the results of the 8714i Meter Verification test as pass or fail. For 
more details on this parameter see Appendix C: Diagnostics.

Simulated Velocity 

Displays the test velocity used to verify transmitter calibration. For more 
details on this parameter see Appendix C: Diagnostics.

Actual Velocity 

Displays the velocity measured by the transmitter during the transmitter 
calibration verification test. For more details on this parameter see 
Appendix C: Diagnostics.

Velocity Deviation 

Displays the deviation of the transmitter calibration verification test. For more 
details on this parameter see Appendix C: Diagnostics.

Transmitter Calibration Result 

Displays the result of the transmitter calibration verification test as pass or fail. 
For more details on this parameter see Appendix C: Diagnostics.

Sensor Calibration Deviation 

Displays the deviation of the sensor calibration verification test. For more 
details on this parameter see Appendix C: Diagnostics.

Sensor Calibration Result 

Displays the result of the sensor calibration verification test as pass or fail. For 
more details on this parameter see Appendix C: Diagnostics.

Coil Circuit Result 

Displays the result of the coil circuit test as pass or fail. For more details on 
this parameter see Appendix C: Diagnostics.

Electrode Circuit Result 

Displays the result of the electrode circuit test as pass or fail. For more details 
on this parameter see Appendix C: Diagnostics.

Trims 

Trims are used to calibrate the analog loop, calibrate the transmitter, re-zero 
the transmitter, and calibrate the transmitter with another manufacturer’s 
sensor. Proceed with caution whenever performing a trim function.

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics, Diagnostic Variables, 8714i Results

375 Transducer Block, Diagnostics

Summary of Contents for 8732 Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands