manualshive.com logo in svg

Rosemount 8732 Series, Reference Manual

The Rosemount 8732 Series, a cutting-edge flow transmitter, is a must-have for precision flow measurement. Enhance your operations with our state-of-the-art equipment by downloading the free Reference Manual. Gain valuable insights and optimize performance. Visit manualshive.com and access your manual today to unlock the full potential of this exceptional product.

Share
Download
background image

Reference Manual 

00809-0100-4663, Rev BA
January 2010

TOC-1

Rosemount 8732

SECTION 1
Introduction

System Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Safety Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Service Support  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

SECTION 2
Installation

Safety Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Transmitter Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Mechanical Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Mount the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Identify Options and Configurations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Hardware Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Conduit Ports and Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
Conduit Cables  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Installation Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Overcurrent Protection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Connect Transmitter Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Connect F

OUNDATION

 fieldbus Wiring  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Transmitter Communication Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Power Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Transmitter Wiring Connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

Sensor Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

Rosemount Sensors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Transmitter to Sensor Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Conduit Cables  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Sensor to Remote Mount Transmitter Connections  . . . . . . . . . . . . . . . . . .2-13

SECTION 3
Configuration

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Local Operator Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Basic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Data Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

LOI Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

Table Value Example  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Select Value Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Display Lock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Start Totalizer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Stop Totalizer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Reset Totalizer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

Diagnostic Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

Review. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

Process Variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

PV - Primary Variable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
PV -% Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
PV - Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
Totalizer Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
Pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7

Table of Contents

Summary of Contents for 8732 Series































































































































































































Reviews:

No comments

Related manuals for 8732 Series

ParTech 8100 Instruction Manual preview
8100
Brand: ParTech Pages: 14
Kawai ES100 Technical Speci? Cations preview
ES100
Brand: Kawai Pages: 5
Jata hogar 80 Instructions Manual preview
80
Brand: Jata hogar Pages: 12
Oldham BM25 Operating Manual preview
BM25
Brand: Oldham Pages: 43
QuadTech 1855 Instruction Manual preview
1855
Brand: QuadTech Pages: 76
PCE Health and Fitness CT 26FN User Manual preview
CT 26FN
Brand: PCE Health and Fitness Pages: 11
Vaisala HUMICAP HM70 Quick Manual preview
HUMICAP HM70
Brand: Vaisala Pages: 40
ProsKit MT-5110 User Manual preview
MT-5110
Brand: ProsKit Pages: 10
TQC Sheen SH1349 Operating Manual preview
SH1349
Brand: TQC Sheen Pages: 16
Omega HHAQ-108 User Manual preview
HHAQ-108
Brand: Omega Pages: 22
Ecodhome 01335-1800-00 Installation Manual preview
01335-1800-00
Brand: Ecodhome Pages: 12
Velleman DCM97K User Manual preview
DCM97K
Brand: Velleman Pages: 13
A&D LC-4101 Series Instruction Manual preview
LC-4101 Series
Brand: A&D Pages: 2
Bulteh 2000 EKOMILK User Manual preview
EKOMILK
Brand: Bulteh 2000 Pages: 80
BIOS dry-cal dc-lite User Manual preview
dry-cal dc-lite
Brand: BIOS Pages: 10
aboni HydroTracer FLV HT2 Operation Manual preview
HydroTracer FLV HT2
Brand: aboni Pages: 48
GARO GNM3T-RS485 Installation And Programming Manual preview
GNM3T-RS485
Brand: GARO Pages: 15
Mountz 070810 Operating Instructions Manual preview
070810
Brand: Mountz Pages: 27

Brands by name

Popular brands

Load more brands