Roland VersaEXPRESS RF-640 User Manual Download Page 65

Page: 65 / 132

Maintenance

Maintenance that Should Be Performed More Than Once a Month

The print-head carriage moves to the right side of the machine, and then
the screen on the left appears.

Remove the cover L.

Attach the cut rail.

Press

Screw

Cut rail

Attach the cover L.

The screen on the left appears and cleaning starts.

When it finishes, the screen on the left appears again.



Press

to go back to the original screen.

Perform a printing test to verify the results of the procedure.

Perform a printing test to check the result.

Perform cleaning using the machine's cleaning feature several times when necessary.



P. 40, "Printing Tests and Cleaning"

OPEN COVER L

REPLACE CUT

RAIL

REPLACE CUT

RAIL

CLOSE COVER L

CLEANING...

MAINTENANCE

CLEANING

Summary of Contents for VersaEXPRESS RF-640





































































































































Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands

Roland VersaEXPRESS RF-640, User Manual

Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands