manualshive.com logo in svg

Roland VersaEXPRESS RF-640, User Manual

Share
Download
Roland VersaEXPRESS RF-640 User Manual Download Page 12

1

Machine 

Highlights

10

Menu List

Main Menu

MENU 

PRESET 

PRESET 

LOAD 

LOAD 

NAME1 

  To [SAVE]

  To [NAME8] 

  To [NAME8]

  To [NAME1] 

Press  

LOAD 

NAME8 

MENU

ADJUST  BI-DIR.

MENU 

CALIBRATION 

CALIBRATION 

SETTING 

CALIBRATION 

TEST  PRINT 

SETTING

+0.10%

-0.10%

  To [SETTING] 

  To [TEST PRINT] 

MENU 

MEDIA  SETTING 

  To [SHEET REMAIN]

PRESET

SAVE

SAVE

NAME1

  

  To [LOAD]

SAVE

NAME8

  To [NAME1]

SET NAME

NAME1

SET NAME

NAME8

ADJUST BI-DIR.

SIMPLE SETTING

ADJUST BI-DIR.

DETAIL SETTING

ADJUST BI-DIR.

TEST PRINT

SIMPLE SETTING

0

    0

DETAIL SETTING

SETTING

DETAIL SETTING

TEST PRINT

To [DETAIL SETTING]

  To [SETTING] 

To [TEST PRINT] 

(*1)

NO.     1      NO.     2

- 15             - 20

NO.     3       NO.     4

- 15             - 20

NO.     5      NO.     6

- 15             - 20

NO.     7       NO.     8

- 15             - 20

Continue

MENU

HEAD HEIGHT

HEAD HEIGHT

HIGH 

    HIGH

To [TEST PRINT] 

(*1) This menu is not displayed when solvent-based ink is used.

Summary of Contents for VersaEXPRESS RF-640





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands