Roland VersaEXPRESS RF-640 User Manual Download Page 117 | Manualshive

Page: 117 / 132

background image

6

FA

Q

Other Problems

115

Has ink run out?

When the screen is displayed, the machine cannot receive the data. If the screen appears during printing, the
machine operation differs according to the setting of "EMPTY MODE". (only RF-640A)



When "STOP" is selected: The printing temporarily stops.



When "CONT." is selected: A warning beep sounds and the printing continues until the machine finishes

printing the received data. You can temporarily stop the printing operation by pressing

.

In either case, replacing the ink cartridge with a new one allows the machine to recover from the error.
If the machine holds the print data that have not been processed, the printing operation is resumed.
If there are unsent data in the computer, resending the data allows printing to be restarted.



P. 49, "How to Replace Ink Cartridges"



P. 98, "Determining What Happens When Ink Runs Out (RF-640A only)"

Is the network routing appropriate?

Try connecting the computer and the machine to the same hub, or connecting them directly using a crossover
cable. If this makes it possible to perform printing, it means the problem is in the network itself.

Are the network settings correct?

If the cable connections are secure and no problem is found in the network itself, make sure that the IP ad-
dress and other such settings are appropriate. The settings on both the machine and the computer must be
appropriate. Ensure that the IP address doesn't conflict with the IP address for another device on the network,
that the port setting for the software RIP specifies the IP address set on the machine, that the settings have
no typing errors, and for other such problems.



"Setup Guide"



P. 103, "Viewing Information About the System of This Machine"

Did the software RIP end abnormally?

Make sure the software RIP is running correctly, then switch the sub power off and back on.



"Roland VersaWorks Quick Start Guide" (RF-640A does not include this)

1 2 3 4
5 6 7

８

«
...
115
116
117
118
119
...
»

Summary of Contents for VersaEXPRESS RF-640





































































































































Reviews:

No comments

Related manuals for VersaEXPRESS RF-640

Brand: MIMAKI Pages: 20

Brand: Furuno Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands