Roland VersaEXPRESS RF-640 User Manual Download Page 68

Page: 68 / 132

Maintenance

Replacing Consumable Parts

Replacing the Wiper

The wiper is the part used for cleaning of the print heads. When such the screen is displayed on the display
screen, it is the time for replacement. Replace it with a new part.

Regarding the purchase of the wiper, contact your authorized Roland DG Corp. dealer or us.

CAUTION

Be sure to perform operations as specified by the following instructions,

and never touch any area not specified in the instructions.

Sudden movement of the machine may cause injury.

Display the [REPLACE WIPER] menu.



When the screen on the left appears, press



Remove any media.



Press

several times until the screen on the left appears.

Press

, and then

twice.

Press

The print-head carriage moves to a location where wiper replacement is
possible, and then the screen on the left appears.

TIME FOR

WIPER REPLACE

Necessary items

TIME FOR

WIPER REPLACE

SUB MENU

MAINTENANCE

REPLACE WIPER

OPEN COVER R

Wiper

Tweezers

Summary of Contents for VersaEXPRESS RF-640





































































































































Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands

Roland VersaEXPRESS RF-640, User Manual

Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands