Roland VersaEXPRESS RF-640 User Manual Download Page 90

Page: 90 / 132

Part of

Practice

Accommodating to the Types and Condition of Media

Using Transparent Media

Set the media type to "CLEAR."



Press



Press

several times until the screen on the left appears.

Press

twice.



Press

to select “CLEAR.”

Press

to enable the setting.

Make the setting for the media width.



Press

, and then



Press



Use

to enter the media width.

Press

to enable the setting.



Press

to go back to the original screen.

Load transparent media to the machine.

Refer to P. 21, "Loading Media" and load media on the machine.

Make the setting for the location of the right edge of the media.



Press



Press

several times until the screen on the left appears.

Press



Press

twice.

Press

The print-head carriage moves to the position now set and the screen on
the left appears.

SUB MENU

SHEET TYPE

OPAQUE CLEAR

SUB MENU

SHEET WIDTH

1371mm 1200mm

SUB MENU

SHEET POS.

SUB MENU

SAVE

Summary of Contents for VersaEXPRESS RF-640





































































































































Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands

Roland VersaEXPRESS RF-640, User Manual

Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands